Dewalt DCF681N2 Instruction Manual - Page 15

Register Online, Accessories, Repairs

Get Dewalt DCF681N2 PDF manuals and user guides View all Dewalt DCF681N2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

English Accessories WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DEWALT recommended accessories should be used with this product. Recommended accessories for use with your tool are available at extra cost from your local dealer or authorized service center. If you need assistance in locating any accessory, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT (1-800-433-9258) or visit our website: www.dewalt.com. Repairs The charger and battery pack are not serviceable. To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement) should be performed by a DEWALT factory service center, a DEWALT authorized service center or other qualified service personnel. Always use identical replacement parts. When deburring becomes difficult a new cutter may be required. INSTALLING REPLACEMENT CUTTER ACCESSORY DWA2601IR (FIG. 8) WARNING: To reduce the risk of serious personal injury, turn tool off and remove the battery pack before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury. 1. Use a 5/64 hex key to loosen and remove set screw (M). 2. Retract cone and tip cutter up and remove. 3. With the slot (N) in the magnetic bit holder and the slot (O) in the cone aligned, insert new cutter (L) sliding the tip under the round wire ring (P) first. Then seat cutter. When seated correctly the cutter should be flush with cone when in forward position. 4. Replace set screw. Align the tip with the hole in the cutter. Tighten firmly. CAUTION: If the set screw is lost or damaged do not replace with anything but an exact replacement part. FIG. 8 M N L P O Register Online Thank you for your purchase. Register your product now for: • WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty service in case there is a problem with your product. • CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft, your registration of ownership will serve as your proof of purchase. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
wire ring  (P) first. Then seat cutter. When seated correctly the
cutter should be flush with cone when in forward position.
4. Replace set screw. Align the tip with the hole in the cutter. Tighten
firmly.
CAUTION:
If the set screw is lost or damaged do not replace with
anything but an exact replacement part.
FIG. 8
M
N
O
P
L
Register Online
Thank you for your purchase. Register your product now for:
•
WARRANTY SERVICE:
Registering your product will help you
obtain more efficient warranty service in case there is a problem
with your product.
•
CONFIRMATION OF OWNERSHIP:
In case of an insurance
loss, such as fire, flood or theft, your registration of ownership will
serve as your proof of purchase.
Accessories
WARNING:
Since accessories, other than those offered by
D
E
WALT, have not been tested with this product, use of such
accessories with this tool could be hazardous. To reduce the risk of
injury, only D
E
WALT recommended accessories should be used with
this product.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service center. If
you need assistance in locating any accessory, please contact
D
E
WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD
21286, call 1-800-4-D
E
WALT (1-800-433-9258) or visit our website:
www.dewalt.com.
Repairs
The charger and battery pack are not serviceable.
To assure product SAFETY and RELIABILITY, repairs, maintenance
and adjustment (including brush inspection and replacement) should
be performed by a D
E
WALT factory service center, a D
E
WALT
authorized service center or other qualified service personnel. Always
use identical replacement parts.
When deburring becomes difficult a new cutter may be required.
INSTALLING REPLACEMENT CUTTER ACCESSORY DWA2601IR
(FIG. 8)
WARNING: To reduce the risk of serious personal injury,
turn tool off and remove the battery pack before making any
adjustments or removing/installing attachments or accessories.
An accidental start-up can cause injury.
1. Use a 5/64 hex key to loosen and remove set screw (M).
2. Retract cone and tip cutter up and remove.
3. With the slot (N) in the magnetic bit holder and the slot (O) in the
cone aligned, insert new cutter (L) sliding the tip under the round
English
13