Dewalt DCF897P2 Instruction Manual - Page 14

Forward/Reverse Control Button Fig. 2, Worklight Fig. 2, Speed Selector Fig. 2, Anvils Fig. 6-9

Get Dewalt DCF897P2 PDF manuals and user guides View all Dewalt DCF897P2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

English Forward/Reverse Control Button (Fig. 2) A forward/reverse control button (B) determines the direction of the tool and also serves as a lock-off button. To select forward rotation, release the trigger switch and depress the forward/reverse control button on the right side of the tool. To select reverse, release the trigger switch and depress the forward/ reverse control button on the left side of the tool. The center position of the control button locks the tool in the OFF position. When changing the position of the control button, be sure the trigger is released. NOTE: The first time the tool is run after changing the direction of rotation, you may hear a click on start up. This is normal and does not indicate a problem. Worklight (Fig. 2) There is a worklight (G) located on the foot of the tool. The worklight is activated when the trigger switch is depressed, and will automatically turn off 20 seconds after the trigger switch is released. If the trigger switch remains depressed, the worklight will remain on. NOTE: The worklight is for lighting the immediate work surface and is not intended to be used as a flashlight. Speed Selector (Fig. 2) Your tool is equipped with a speed selector (K) which allows you to select one of three speeds. Select the speed based on the application and control the speed of the tool using the variable speed trigger switch (A). Speed 1 0-400 rpm Speed 2 0-1200 rpm Speed 3 0-1900 rpm Anvils (Fig. 6-9) WARNING: Use only impact accessories. Non-impact accessories may break and cause a hazardous condition. Inspect accessories prior to use to ensure that it cont­ains no cracks. CAUTION: Inspect anvils, detent pins and hog rings prior to use. Missing or damaged items should be replaced before use. Place the switch in the locked off (center) position or remove battery pack before changing accessories. ANVIL WITH DETENT PIN (FIG. 6) DCF899 FIG. 6 C To install an accessory on the anvil, align the hole in the side of the accessory with the detent pin (H) on the anvil (C). Press the accessory on until the detent pin engages in the hole. Depression of detent pin may be necessary to aid installation of accessory. To remove an accessory, depress the detent pin through the hole and pull the accessory off. H ANVIL WITH HOG RING (FIG. 7, 8) DCF897, DCF899H DCF899 To install an accessory on the hog ring anvil, firmly push accessory onto the anvil (C). The hog ring (I) compresses to allow the accessory to slide on. After accessory is installed, the hog ring applies pressure to help provide accessory retention. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Forward/Reverse Control Button (Fig. 2)
A forward/reverse control button (B) determines the direction of the
tool and also serves as a lock-off button.
To select forward rotation, release the trigger switch and depress the
forward/reverse control button on the right side of the tool.
To select reverse, release the trigger switch and depress the forward/
reverse control button on the left side of the tool.
The center position of the control button locks the tool in the OFF
position. When changing the position of the control button, be sure
the trigger is released.
NOTE:
The first time the tool is run after changing the direction of
rotation, you may hear a click on start up. This is normal and does
not indicate a problem.
Worklight (Fig. 2)
There is a worklight (G) located on the foot of the tool. The worklight is
activated when the trigger switch is depressed, and will automatically
turn off 20 seconds after the trigger switch is released. If the trigger
switch remains depressed, the worklight will remain on.
NOTE:
The worklight is for lighting the immediate work surface and is
not intended to be used as a flashlight.
Speed Selector (Fig. 2)
Your tool is equipped with a speed selector (K) which allows you to
select one of three speeds. Select the speed based on the application
and control the speed of the tool using the variable speed trigger
switch (A).
Speed 1
0–400 rpm
Speed 2
0–1200 rpm
Speed 3
0–1900 rpm
Anvils (Fig. 6–9)
WARNING:
Use only impact accessories. Non-impact accessories
may break and cause a hazardous condition. Inspect accessories
prior to use to ensure that it contains no cracks.
CAUTION:
Inspect anvils, detent pins and hog rings prior to use.
Missing or damaged items should be replaced before use.
Place the switch in the locked off (center) position or remove battery
pack before changing accessories.
ANVIL WITH DETENT PIN (FIG. 6)
FIG. 6
H
C
DCF899
DCF899
To install an accessory on the anvil,
align the
hole in the side of the accessory with the detent
pin (H) on the anvil (C). Press the accessory
on until the detent pin engages in the hole.
Depression of detent pin may be necessary to aid
installation of accessory.
To remove an accessory,
depress the detent
pin through the hole and pull the accessory off.
ANVIL WITH HOG RING (FIG. 7, 8)
DCF897, DCF899H
To install an accessory on the hog ring anvil,
firmly push
accessory onto the anvil (C). The hog ring (I) compresses to allow the
accessory to slide on. After accessory is installed, the hog ring applies
pressure to help provide accessory retention.
English
12