Dewalt DWC860W Instruction Manual

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA.

ADVERTENCIA:

LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

Deﬁnitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read the

manual and pay attention to these symbols.

DANGER:

Indicates an imminently hazardous situation which, if not avoided,

will

result in

death or serious injury

.

WARNING:

Indicates a potentially hazardous situation which, if not avoided,

could

result in

death or serious injury

.

CAUTION

: Indicates a potentially hazardous situation which, if not avoided,

may

result

in

minor or moderate injury

.

NOTICE:

Indicates a practice

not related to personal injury

which, if not avoided,

may

result in

property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D

E

WALT TOOL,

CALL US TOLL FREE AT:

1-800-4-D

E

WALT (1-800-433-9258).

WARNING:

To reduce the risk of injury, read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and instructions

Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury.

SAVE THESE INSTRUCTIONS

WORK AREA

•

Keep your work area clean and well lit.

Cluttered benches and dark areas invite

accidents.

•

Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust.

Power tools create sparks which may ignite the dust or

fumes.

•

Keep bystanders, children, and visitors away while operating a power tool.

Distractions

can cause you to lose control.

ELECTRICAL SAFETY

•

Double insulated tools are equipped with a polarized plug (one blade is wider than the

other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully

in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to

install a polarized outlet. Do not change the plug in any way.

Double insulation

eliminates the need for the three wire grounded power cord and grounded power supply

system.

•

Avoid body contact with grounded surfaces such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if your body is grounded.

•

Don’t expose power tools to rain or wet conditions.

Water entering a power tool will

increase the risk of electric shock.

•

Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an

outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged

cords immediately.

Damaged cords increase the risk of electric shock.

•

When operating a power tool outside, use an outdoor extension cord marked “W-A”

or “W.”

These cords are rated for outdoor use and reduce the risk of electric shock. When

using an extension cord, be sure to use one heavy enough to carry the current your product

will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and

overheating. The following table shows the correct size to use depending on cord length

and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage

number, the heavier the cord.

Minimum Gauge for Cord Sets

Ampere Rating

Volts

Total Length of Cord in Feet (meters)

120V

25 (7.6)

50 (15.2)

100 (30.5)

150 (45.7)

240V

50 (15.2)

100 (30.5)

200 (61.0)

300 (91.4)

MoreThan

Not More Than

AWG

0

6

18

16

16

14

6

10

18

16

14

12

10

12

16

16

14

12

12

16

14

12

Not Recommended

PERSONAL SAFETY

•

Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication.

A moment of inattention while operating power tools may result in serious personal injury.

•

Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair,

clothing, and gloves away from moving parts.

Loose clothing, jewelry, or long hair can be

caught in moving parts. Air vents often cover moving parts and should also be avoided.

•

Avoid accidental starting. Be sure switch is off before plugging in.

Carrying tools with

your finger on the switch or plugging in tools that have the switch on invites accidents.

•

Remove adjusting keys or wrenches before turning the tool on.

A wrench or a key that

is left attached to a rotating part of the tool may result in personal injury.

•

Do not overreach. Keep proper footing and balance at all times.

Proper footing and

balance enables better control of the tool in unexpected situations.

•

Use safety equipment. Always wear eye protection.

Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

•

Use clamps or other practical way to secure and support the workpiece to a stable

platform.

Holding the work by hand or against your body is unstable and may lead to loss of

control.

•

Do not force tool. Use the correct tool for your application.

The correct tool will do the job

better and safer at the rate for which it is designed.

•

Do not use tool if switch does not turn it on or off.

Any tool that cannot be controlled with

the switch is dangerous and must be repaired.

•

Disconnect the plug from the power source before making any adjustments, changing

accessories, or storing the tool.

Such preventative safety measures reduce the risk of

starting the tool accidentally.

•

Store idle tools out of reach of children and other untrained persons.

Tools are

dangerous in the hands of untrained users.

•

Maintain tools with care. Keep cutting tools sharp and clean.

Properly maintained tools,

with sharp cutting edges are less likely to bind and are easier to control.

•

Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tool’s operation. If damaged, have the tool serviced before

using.

Many accidents are caused by poorly maintained tools.

•

Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used on

another tool.

SERVICE

•

Tool service must be performed only by qualified repair personnel.

Service or

maintenance performed by unqualified personnel could result in a risk of injury.

•

When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual.

Use of unauthorized parts or failure to follow

maintenance instructions may create a risk of electric shock or injury.

Additional Speciﬁc Safety Instructions for Masonry Saws

•

DANGER! Keep hands away from cutting area and blade. Keep your second hand on

auxiliary handle or motor housing.

If both hands are holding the saw, they cannot be cut

by the blade.

•

Do not reach underneath the workpiece.

The guard cannot protect you from the blade

below the workpiece

•

Never hold piece being cut in your hands or across your leg. Secure the workpiece to

a stable platform.

It is important to support the work properly to minimize body exposure,

blade binding, or loss of control.

• Hold tool by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord.

Contact with a "live" wire will also

make exposed metal parts of the power tool "live" and shock the operator.

•

Always use blades with correct size and shape (diamond versus round) of arbor holes.

Blades that do not match the mounting hardware of the saw will run eccentrically, causing

loss of control.

•

Never use damaged or incorrect blade washers or bolt.

The blade washers and bolt were

specially designed for your saw, for optimum performance and safety of operation.

•

Keep your body positioned to either side of the blade, but not in line with the saw

blade.

•

Blades coast after turn off. Serious personal injury may result.

•

Don’t unplug if plug or receptacle is wet.

Disconnect the fuse or circuit breaker that supplies

power to the tool. Then unplug and examine for presence of water in the receptacle.

•

Wait for the saw to come to a complete stop.

An unprotected, coasting blade will cause

the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the

blade to stop after switch is released.

•

Do not use to cut wood or metal.

•

Never use toothed blades.

This tool is not equipped with a

lower guard.

DANGER: Keep hands away from cutting area and blade.

Personal injury may result.

WARNING:

Always plug extension cord into a GFCI protected outlet.

WARNING:

To reduce the risk of electrocution, keep all connections

dry and off the ground. Do not touch plug with wet hands.

WARNING:

A Ground Fault Circuit Interrupter (GFCI) is provided on the cord set. Receptacles

are available having built in GFCI protection and may be used for an added measure of safety.

When using an extension cord, always plug into a GFCI protected receptacle or outlet.

WARNING:

Test GFCI before each use:

1. Plug GFCI into power outlet. Indicator should turn red.

2. Press test button. Red indicator should disappear.

3. Press reset button for use. Do not use if above test fails.

WARNING:

Never use saw with salt water or a conductive fluid.

WARNING: DO NOT

use wet cutting when using bonded abrasive blades. Wheel rupture and

personal injury may result.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known in the state of California to cause cancer, birth

defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work.

To reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter out

microscopic particles.

•

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed

areas with soap and water.

Allowing dust to get into your mouth, eyes, or lay on the

skin may promote absorption of harmful chemicals.

WARNING:

Use of this tool can generate and/or disburse dust, which may cause serious

and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory

protection appropriate for the dust exposure. Direct particles away from face and body. Always

operate tool in well-ventilated area and provide for proper dust removal. Use dust collection

system wherever possible.

WARNING: ALWAYS wear proper personal hearing protection during use.

Under some

conditions and duration of use, noise from this product may contribute to hearing loss.

WARNING: ALWAYS use eye protection.

All users and bystanders must wear eye

protection that conforms to ANSI Z87.1.

•

The label on your tool may include the following symbols. The symbols and their definitions

are as follows:

V

...................

volts

A

....................

amperes

Hz

.................

hertz

W

...................

watts

min

...............

minutes

..................

alternating current

............

direct current

..................

alternating or direct current

.................

Class I Construction

n

o

..................

no load speed

.....................

(grounded)

...................

earthing terminal

.................

Class II Construction

..................

safety alert symbol

.....................

(double insulated)

…/min

............

per minute

BPM

.............

beats per minute

IPM

................

impacts per minute

RPM

.............

revolutions per minute

D

E

WALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286

(JUN10)

Part No. N073473

DWC860W

Copyright © 2010 D

E

WALT

The following are trademarks for one or more D

E

WALT power tools: the yellow and black color scheme; the

“D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of

lozenge-shaped humps on the surface of the tool.

DWC860W Heavy-Duty 4-3/8" (110 mm) Wet/Dry Masonry Saw

Scie industrielle à maçonnerie à sec/à l’eau DWC860W de 110 mm (4-3/8 po)

Sierra industrial de 110 mm (4-3/8 pulg.) de corte húmedo o seco

para mampostería DWC860W

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-D

E

WALT • www.dewalt.com

Dewalt DWC860W Instruction Manual

Dewalt DWC860W Manual

Dewalt DWC860W manual content summary: