Electrolux E36DF76TPS Installation Instructions English - Page 15

Drill Pilot Holes and Fasten Bracket, Check Level and Position the Range

Get Electrolux E36DF76TPS PDF manuals and user guides View all Electrolux E36DF76TPS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

30" & 36" DUAL FUEL RANGE INSTALLATION INSTRUCTIONS 8.2 Drill Pilot Holes and Fasten Bracket Drill a 1/8" pilot hole where screws are to be located. If bracket is to be mounted to the wall, drill pilot hole at an approximate 20° downward angle. If bracket is to be mounted to masonry or ceramic floors, drill a 3/16" (4.8 mm) pilot hole 1-3/4" deep. 8.3 Check Level and Position the Range Check the level of the final installation. Note: A minimum clearance of 1/8" is required between the bottom of the range and the levelling leg to allow room for the bracket. Use a spirit level to check your adjustments. Figure 23: Drill pilot holes The screws provided may be used in wood or concrete material. Use a 5/16" nut-driver or flat head screwdriver to secure the bracket in place. Leveling Leg Anti-Tip Bracket Figure 25: Use the oven racks to level appliance 1/8" Minimum Wall Mount Wall Plate Slide range into position. Floor Mount Figure 24: Fastening the bracket Figure 26: Slide appliance into bracket To check if the anti-tip bracket is installed properly, use both arms and grasp the rear edge of range back. Carefully attempt to tilt range forward. When properly installed, the range should not tilt forward. If range is moved to a different location, the anti-tip brackets must also be moved and installed with the range. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
15
30" & 36" DUAL FUEL RANGE INSTALLATION INSTRUCTIONS
8.2
Drill Pilot Holes and Fasten Bracket
Drill a 1/8” pilot hole where screws are to be located.
If bracket is to be mounted to the wall, drill pilot hole at
an approximate 20° downward angle. If bracket is to
be mounted to masonry or ceramic floors, drill a 3/16”
(4.8 mm) pilot hole 1-3/4” deep.
Leveling Leg
Anti-Tip Bracket
Floor Mount
1/8" Minimum
Wall Plate
Wall Mount
Figure 24: Fastening the bracket
8.3
Check Level and Position the Range
Check the level of the final installation. Note: A minimum
clearance of 1/8” is required between the bottom of the
range and the levelling leg to allow room for the bracket.
Use a spirit level to check your adjustments.
Figure 23: Drill pilot holes
The screws provided may be used in wood or concrete
material.
Use a 5/16” nut-driver or flat head screwdriver to
secure the bracket in place.
Slide range into position.
To check if the anti-tip bracket is installed properly,
use both arms and grasp the rear edge of range back.
Carefully attempt to tilt range forward. When properly
installed, the range should not tilt forward.
If range is moved to a different location, the anti-tip
brackets must also be moved and installed with the range.
Figure 25: Use the oven racks to level appliance
Figure 26: Slide appliance into bracket