Epson Apex 386SX/20 Canadian Product User Manual - Page 73

Entering the Setup Program, Pressing <F1> to Enter the Setup Program

Get Epson Apex 386SX/20 Canadian Product PDF manuals and user guides View all Epson Apex 386SX/20 Canadian Product manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Entering the Setup Program There are two ways to enter the setup program: by pressing or by pressing . 1. Pressing to Enter the Setup Program You will need to press , to enter the setup program in the following situations: Ž when your computer is turned on for the first time Ž when the rechargeable battery is dead Ž when the hardware configuration is changed If the battery for CMOS chip is dead or the system configuration does not match your actual hardware configuration, you will have to reconfigure your system. The computer will give you this screen message: Press the F1 key to enter the setup program or press any other key to continue Under the above three conditions, pressing will automatically start the setup program. Under any conditions within DOS, you can use the DOS DEBUG command as follows: A> DEBUG 8 -g=F000:FF60 8 This command will start the setup program. 12 Chapter 3: Operating Your System

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
Entering the Setup Program
There are two ways to enter the setup program: by pressing
<F1>
or
by pressing
<ESC>.
1. Pressing <F1> to Enter the Setup Program
You will need to press
<F1>,
to enter the setup program in the following
situations:
Ž when your computer is turned on for the first time
Ž when the rechargeable battery is dead
Ž when the hardware configuration is changed
If the battery for CMOS chip is dead or the system configuration does
not match your actual hardware configuration, you will have to recon-
figure your system. The computer will give you this screen message:
Press the F1 key to enter the setup program or
press any other key to continue
Under the above three conditions, pressing
<F1>
will automatically
start the setup program.
Under any conditions within DOS, you can use the DOS DEBUG
command as follows:
A> DEBUG
8
-g=F000:FF60
8
This command will start the setup program.
12
Chapter 3: Operating Your System