Epson BrightLink 695Wi Installation Guide - Ultra-Short Throw Wall Mount ELPMB - Page 35

Adjusting the Image - touch calibration

Get Epson BrightLink 695Wi PDF manuals and user guides View all Epson BrightLink 695Wi manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

English 6 Adjusting the Image To ensure the best image quality, follow the steps below to adjust the projected image. Do not make adjustments with the Quick Corner or Keystone functions of the projector. Doing so may result in a reduction in image quality and pen or finger touch calibration. Follow these guidelines for setting up the projector: • Make sure the image is evenly rectangular, without distortion. • Make sure the projector is tilted no more than 3° vertically and horizontally in relation to the projected image. Your remote control or projector control panel may look different from the illustrations in this section, but the instructions are the same except where noted. A Turn on the projector Remote Control Control Panel B Change the aspect ratio if necessary Each time you press the [Aspect] button on the remote control, the aspect name is displayed on the screen and the aspect ratio changes. You will need to re-display the test pattern after changing the aspect ratio. Change the setting according to the signal for the connected equipment. You will need to project content from a connected device in order to change the aspect ratio. Remote Control Aspect Ratio Normal Alternatively, set the aspect ratio from the Signal menu - Aspect. Following is a list of available aspect settings: BrightLink 480i and PowerLite 470/480/570/580/680 • Auto: Automatically sets the aspect ratio according to the input signal and the Resolution setting (available only for HDMI image sources). 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
35
English
6
Adjusting the Image
To ensure the best image quality, follow the steps below to adjust the projected image.
Follow these guidelines for setting up the projector:
•
Make sure the image is evenly rectangular, without distortion.
•
Make sure the projector is tilted no more than 3° vertically and horizontally in relation to the projected
image.
A
Turn on the projector
B
Change the aspect ratio if necessary
Each time you press the [Aspect] button on the remote control, the aspect name is displayed on the
screen and the aspect ratio changes. You will need to re-display the test pattern after changing the
aspect ratio.
Change the setting according to the signal for the connected equipment.
Alternatively, set the aspect ratio from the Signal menu -
Aspect. Following is a list of available aspect
settings:
BrightLink 480i and PowerLite 470/480/570/580/680
•
Auto:
Automatically sets the aspect ratio according to the input signal and the
Resolution
setting
(available only for HDMI image sources).
Do not make adjustments with the Quick Corner or Keystone functions of the
projector. Doing so may result in a reduction in image quality and pen or finger touch
calibration.
Your remote control or projector control panel may look different from the
illustrations in this section, but the instructions are the same except where noted.
Remote Control
Control Panel
You will need to project content from a connected device in order to change the aspect
ratio.
Remote Control
Normal
Aspect Ratio