Eureka AirSpeed ONE AS2001TIS Owner's Guide - Page 1

AS2000-AS2039 Series OWNER'S GUIDE For detailed vacuum information including FAQs please visit eureka.com or call the Customer Service Helpline: 1-800-282-2886. 8 a.m. to 7:30 p.m. (CST), Monday - Friday 10 a.m. to 6:30 p.m. (CST), Saturday - Sunday • This vacuum cleaner creates suction. Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts. • Do not place vacuum on furniture or stairs as the brush roll may cause damage. • Use extra care when cleaning on stairs. Do not place vacuum at top of stairs. • Use extra care when cleaning area rugs as the brush roll may cause damage. • Unplug before connecting turbo nozzle (if supplied) or other attachments. Place vacuum on floor with the handle in upright position while using attachments. • Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes. • Do not use without dust cup or filter(s) in place. • Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas where they may be present. • Store your vacuum indoors in a cool, dry area. • Keep your work area well lighted. • Unplug electrical appliances before vacuuming them. • Brush roll could suddenly restart. Unplug before servicing. www.eureka.com © 2013 Electrolux Home Care Products, Inc. Printed in China PN 090211_rev3 SAVE THESE INSTRUCTIONS FOR HOUSEHOLD USE ONLY To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. Do not oil the motor or brush roll at any time, the bearings are permanently lubricated and sealed. IMPORTANT SAFEGUARDS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER. WARNING To reduce the risk of fire, electric shock, or injury: • Do not use outdoors or on wet surfaces. • Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug the electrical cord when not in use and before servicing. • Do not allow to be used as a toy. Close attention is necessary when used by or near children. • Use only as described in this manual. Use only manufacturer's recommended attachments. • Do not use with damaged cord or plug. If vacuum cleaner is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center before using. • Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run vacuum cleaner over cord. Keep cord away from heated surfaces. • Do not use extension cords or outlets with inadequate current carrying capacity. • Turn off all controls before unplugging. • Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. • Do not handle plug or vacuum cleaner with wet hands. • Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow. Easy 4 Step Assembly To view our "How to Assemble" demo, visit www.eureka.com/airspeed/assembly STEP STEP STEP STEP 1 2 3 4 Fig. 1 B A Alternate View B A Hose Retainer C Fig. 2 B B A Fig 1: With the backbone (B) loosely on the base (A), rotate the backbone forward until the vaccum is locked in the upright position. Fig 2: stand as shown and push down on backbone (B) valve to snap into place. Pull up to ensure the backbone has locked properly. Align so that the hose retainer on the handle (C) is facing the vacuum front. Lower the handle (C) onto the backbone (B). Push down to snap into place. Pull up to ensure the handle has locked properly. Put dust cup (D) into place on base. Push cup handle toward backbone (B) to snap into place. To attach hose connector, align tabs and lower hose onto connector. Turn clockwise to lock. Hose and Tool Storage Hose Retainer E C G H I E Route hose (E) through hose retainer on front of handle (C). Put hose end (E) into hook at base of tool clips. Then push hose into clips. Slide crevice tool (F) into top of extension wand end (G). Place into clips on the side of the vacuum. Store dusting brush (H) on back of vacuum. On some models: Attach turbo nozzle (I) to clip on handle (C). What's In The Carton Base (A) Backbone (B) Handle (C) Dust Cup (D) Maintenance Cleaning the Dustcup Cleaning the Filter Latch Screen Dustcup Hold dust cup handle in one hand and the bottom of dust cup in the other, turn dust cup counter clockwise to unlock the cup from the lid. Empty the dust cup into the trash container. Wipe debris off screen. Replacing the Belt Hold dust cup handle in one hand and the bottom of dust cup in the other, line up arrow on dust cup with unlock icon on backside of dust cup. Turn clockwise to lock the cup to the lid. Pull dust cup latch to release dust cup. Remove filter and wash. Allow to air dry thoroughly (24 hours) before placing back in dust cup Hose (E) Crevice Tool (F) Extension Wand (G) Dusting Brush (H) Turbo nozzle (I) Note: Remove Crevice Tool (F) and Extension Wand (G) from inside of Backbone (B) hole before assembly. Unplug vacuum. Recline cleaner back. Using Philips screwdriver, remove 4 screws from hood. Using thumbs, push down on height adjust knob, while pulling up on inside hood edges with fingers. Lift and remove hood. Lift left side of brushroll out of grooves. Then lift right side of brushroll out of grooves. Get Ready to Vacuum To vacuum floors, turn air path knob to 'floors.' Adjust height for carpet or bare floors. Step on foot graphic on hood and pull back on handle to recline vacuum. Step on power switch to turn on; step on again to turn off. If desired, route cord through cord clips before storing on hooks For hose cleaning turn air path knob to "tools". Attach tools to end of wand. To replace, store crevice tool inside extension wand and store this, dusting brush and turbo nozzle (for some models) in clips. Remove belt from the brushroll and motor shaft. Loop new belt over motor shaft and brushroll, onto grey belt pulley. Grip the brushroll and belt as shown. Stretch belt and push the right side of brushroll into grooves. Lower left side of brushroll into grooves making sure both sides are secure by pushing down. Rotate the brushroll with hands to make sure belt is in center of gray pulley. Line up corners of hood and put hood tab inside the front of cleaner. From front to back, push hood onto base, keeping hood in base grooves, and line up 4 screw holes. Replace 4 screws. Registration To register your product visit www.eureka.com and click on the 'Register Your Product' link in the top right corner. Eureka Limited Warranty For full warranty details, please refer to the additional instructions at www.eureka.com or call the customer service helpline at 1-800-282-2886. Maintenance Schedule Make sure vacuum cleaner is turned off and power cord is unplugged when performing any maintenance. For maintenance information, see maintenance section in this guide, see backside of dust cup or visit www.eureka.com. Maintenance not described must be performed by an authorized dealer. DUST CUP - Empty after each use FILTER DCF26 - Replace or clean regularly to maintain suction U BELT - Check and replace if worn, cut or out of shape BRUSHROLL - Clean monthly Thermal Cutoff This vacuum cleaner has a special thermostat that protects the vacuum in case of motor overheating. If the vacuum suddenly shuts off proceed as follows: 1) Push the on/off switch off (l) and unplug the vacuum. 2) Check the vacuum for a possible source of overheating such as a full dust cup, a blocked hose or clogged filter. If these conditions are found, fix them and wait at least 30 minutes before attempting to use the vacuum. 3) After the 30 minute period, plug the vacuum back in and push the on/off switch on (l). If the vacuum still does not work, call the Eureka customer service helpline. Problem Solving For questions and problems related to your vacuum, please visit www.eureka.com or call the Customer Service Helpline: 1-800-282-2886. www.eureka.com © 2013 Electrolux Home Care Products, Inc. Printed in China PN 090211_rev3