Foxconn G43MX-K English Manual. - Page 37

► Memory Speed Adjust, ► Memory Timing by SPD, ► IGD Graphics Mode Select, ► IGD GTT Graphic Memory

Get Foxconn G43MX-K PDF manuals and user guides View all Foxconn G43MX-K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

3 occupy that 3.5-4GB address space and re-map it into the 4.0-4.5 address space. The RAM doesn't care because it's just an array of storage cells, it's up to the memory controller to as sociate addresses with those storage cells. Of course, that only works if you're using a 64-bit (or 32bit physical address extension (PAE) enabled) OS that can deal with physical addresses larger than 32 bits. Once this option is enabled, the BIOS can see 8192 MB of memory. ► Memory Speed Adjust This item is used to adjust the memory speed. Select [Auto] for SPD enable mode.You also can select a value manually such as [667 MHz] or [800 MHz]. ► Memory Timing by SPD This item is used to enable/disable provision of DRAM timing by SPD device. The Serial Presence Detect (SPD) device is a small EEPROM chip, mounted on a memory module. It contains important information about the module's speed, size, addressing mode and various other parameters, so that the motherboard memory controller (chipset) can better access the memory device. ► IGD Graphics Mode Select This item is used to select the amount of system memory used by internal graphics device. ► IGD GTT Graphic Memory Size This item shows the amount of main memory that is pre-allocated to support the Internal Graphics Translation Table (0-2MB). ► PEG Port This item is used to enable/disable PCI Express graphics port. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
3
30
occupy that 3.5-4GB address space and re-map it into the 4.0-4.5 address space. The RAM
doesn't care because it's just an array of storage cells, it's up to the memory controller to as
sociate addresses with those storage cells.
Of course, that only works if you're using a 64-bit (or 32bit physical address extension (PAE)
enabled) OS that can deal with physical addresses larger than 32 bits.
Once this option is enabled, the BIOS can see 8192 MB of memory.
► Memory Speed Adjust
This item is used to adjust the memory speed.
Select [Auto] for SPD enable mode.
You also
can select a value manually such as [667 MHz] or [800 MHz].
► Memory Timing by SPD
This item is used to enable/disable provision of DRAM timing by SPD device. The Serial
Presence Detect (SPD) device is a small EEPROM chip, mounted on a memory module. It
contains important information about the module's speed, size, addressing mode and various
other parameters, so that the motherboard memory controller (chipset) can better access the
memory device.
► IGD Graphics Mode Select
This item is used to select the amount of system memory used by internal graphics device.
► IGD GTT Graphic Memory Size
This item shows the amount of main memory that is pre-allocated to support the Internal
Graphics Translation Table (0-2MB).
► PEG Port
This item is used to enable/disable PCI Express graphics port.