Garmin ECHOMAP Plus 44cv Installation Instructions - Page 2

Installing the Swivel Base, Installing the Cables and Connectors

Get Garmin ECHOMAP Plus 44cv PDF manuals and user guides View all Garmin ECHOMAP Plus 44cv manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

Installing the Swivel Base Fastening the Swivel Mount without the Cables Running through the Mount You should complete this procedure only if you are not running the power and transducer cables under the mounting surface and through the swivel-mount base. 1 Place the base on the mounting surface, and fasten it using the appropriate screws or bolts . 2 Place the swivel mount on the base, and replace the 10 mm M6×1 Phillips screw. 3 Seal the cable pass-through holes with marine sealant. Preparing to Run Cables under the Mounting Surface NOTICE Use pan-head screws or bolts when securing the swivel-mount base. Screws or bolts with countersunk heads damage the base. Before you can prepare the swivel-mount base, you must choose the location to install the mount and decide whether to attach the mount using screws or bolts. 1 Remove the 10 mm M6x1 Phillips screw and separate the swivel mount from the base . 5 Using the appropriate drill bit for the hardware, drill the three pilot holes. 6 Using a 16 mm (5/8 in.) drill bit, drill the cable-routing hole. Fastening the Swivel Mount with the Cables Running through the Mount You should complete this procedure only when running the power and transducer cables under the mounting surface and through the swivel-mount base. 1 Feed the cables through the 16 mm (5/8 in.) center hole you drilled when preparing to run cables beneath the mounting surface. 2 Place the base on the mounting surface. 3 Route the cables through the cable pass-through holes. 4 Loosely fasten the base using the appropriate screws or bolts. 5 Place the swivel mount on the base, but do not fasten it. 6 Place the cradle or device into the swivel mount (Installing the Device in the Cradle, page 4). 7 Pull out enough slack from the power and transducer cables so the mount can fully swivel to the desired positions when the cables are connected. 8 Remove the cradle and the swivel mount from the base. 9 Apply marine sealant to the 16 mm (5/8 in.) center hole and to the cable pass-through holes. 10Securely fasten the base with the appropriate screws or bolts. 11Place the swivel mount on the base, and fasten it using the included 10 mm M6×1 Phillips screw. Installing the Cradle in the Mount 1 Pull up the locking arm . 2 Orient the swivel base so the pass-through holes face the desired direction. 3 Using the swivel base as a template, mark the pilot hole locations . 4 Mark the cable routing hole . 2 Place the cradle into the swivel mount . 3 Tilt the mount to the desired viewing angle. 4 Press down the locking arm. Installing the Cables and Connectors Wiring to Power 1 Route the power cable from the mount to the boat battery or fuse block. 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
Installing the Swivel Base
Fastening the Swivel Mount without the Cables
Running through the Mount
You should complete this procedure only if you are not running
the power and transducer cables under the mounting surface
and through the swivel-mount base.
1
Place the base
on the mounting surface, and fasten it
using the appropriate screws or bolts
.
2
Place the swivel mount on the base, and replace the 10 mm
M6×1 Phillips screw.
3
Seal the cable pass-through holes with marine sealant.
Preparing to Run Cables under the Mounting Surface
NOTICE
Use pan-head screws or bolts when securing the swivel-mount
base. Screws or bolts with countersunk heads damage the
base.
Before you can prepare the swivel-mount base, you must
choose the location to install the mount and decide whether to
attach the mount using screws or bolts.
1
Remove the 10 mm M6x1 Phillips screw
and separate the
swivel mount
from the base
.
2
Orient the swivel base so the pass-through holes
face the
desired direction.
3
Using the swivel base as a template, mark the pilot hole
locations
.
4
Mark the cable routing hole
.
5
Using the appropriate drill bit for the hardware, drill the three
pilot holes.
6
Using a 16 mm (
5
/
8
in.) drill bit, drill the cable-routing hole.
Fastening the Swivel Mount with the Cables Running
through the Mount
You should complete this procedure only when running the
power and transducer cables under the mounting surface and
through the swivel-mount base.
1
Feed the cables through the 16 mm (
5
/
8
in.) center hole you
drilled when preparing to run cables beneath the mounting
surface.
2
Place the base on the mounting surface.
3
Route the cables through the cable pass-through holes.
4
Loosely fasten the base using the appropriate screws or
bolts.
5
Place the swivel mount on the base, but do not fasten it.
6
Place the cradle or device into the swivel mount (
Installing
the Device in the Cradle
, page 4
).
7
Pull out enough slack from the power and transducer cables
so the mount can fully swivel to the desired positions when
the cables are connected.
8
Remove the cradle and the swivel mount from the base.
9
Apply marine sealant to the 16 mm (
5
/
8
in.) center hole and to
the cable pass-through holes.
10
Securely fasten the base with the appropriate screws or
bolts.
11
Place the swivel mount on the base, and fasten it using the
included 10 mm M6×1 Phillips screw.
Installing the Cradle in the Mount
1
Pull up the locking arm
.
2
Place the cradle into the swivel mount
.
3
Tilt the mount to the desired viewing angle.
4
Press down the locking arm.
Installing the Cables and Connectors
Wiring to Power
1
Route the power cable from the mount to the boat battery or
fuse block.
2