Garmin nuvi 65LM Owner's Manual - Page 15

About: Displays the software version number, the unit ID number, and information on several other software features. EULAs: Displays the end-user license agreements that apply to your choice. NOTE: You need this information when you update the system software or purchase additional map data. Travel History: Allows the device to record information for the myTrends™, Where I've Been, and Trip Log features. Clear Travel History: Clears your travel history for the myTrends, Where I've Been, and Trip Log features. Restoring Settings You can restore a category of settings or all settings to the factory default values. 1 Select Settings. 2 If necessary, select a settings category. 3 Select > Restore. Appendix Power Cables Your device can be powered various ways. • Vehicle power cable • USB cable • AC adapter (optional accessory) Charging the Device NOTE: This Class III product shall be powered by an LPS power supply. You can charge the battery in the device using any of these methods. • Connect the device to the vehicle power cable. • Connect the device to a computer using a USB cable. The device may charge slowly when connected to a computer. Some portable computers may not charge the device. • Connect the device to an optional power adapter accessory, such as a wall power adapter. You can purchase an approved Garmin AC-DC adapter suitable for home or office use from a Garmin dealer or www.garmin.com. Changing the Fuse in the Vehicle Power Cable NOTICE When replacing the fuse, do not lose any of the small pieces and make sure they are put back in the proper position. The vehicle power cable does not work unless it is assembled correctly. If your device does not charge in your vehicle, you may need to replace the fuse located at the tip of the vehicle adapter. 1 Rotate the end piece À 90 degrees counter clockwise to unlock it. TIP: You may need to use a coin to remove the end piece. 2 Remove the end piece, the silver tip Á, and the fuse Â. 3 Insert a new fast-blow fuse that has the same current, such as 1 A or 2 A. 4 Place the silver tip in the end piece. 5 Push in the end piece and rotate it 90 degrees clockwise to lock it back into the vehicle power cable Ã. Device Care NOTICE Avoid dropping your device. Do not store the device where prolonged exposure to extreme temperatures can occur, because it can cause permanent damage. Never use a hard or sharp object to operate the touchscreen, or damage may result. Cleaning the Outer Casing NOTICE Avoid chemical cleaners and solvents that can damage plastic components. 1 Clean the outer casing of the device (not the touchscreen) using a cloth dampened with a mild detergent solution. 2 Wipe the device dry. Cleaning the Touchscreen 1 Use a soft, clean, lint-free cloth. 2 If necessary, lightly dampen the cloth with water. 3 If using a dampened cloth, turn off the device and disconnect the device from power. 4 Gently wipe the screen with the cloth. Avoiding Theft • Remove the device and mount from sight when not in use. • Remove the residue left on the windshield by the suction cup. • Do not keep your unit in the glove compartment. • Register your device at http: / / my .garmin .com. Mounting on Your Dashboard NOTICE The permanent mounting adhesive is extremely difficult to remove after it is installed. You can use an optional mounting disk to mount your device to the dashboard and comply with certain state regulations. See www.garmin.com for more information. 1 Clean and dry the dashboard where you are placing the disk. 2 Remove the backing from the adhesive on the bottom of the disk. 3 Place the disk on the dashboard. 4 Remove the clear plastic cover from the top of the disk. 5 Place the suction cup mount on top of the disk. 6 Flip the lever down (toward the disk). Removing the Device, Mount, and Suction Cup Removing the Device from the Mount 1 Press the release tab or button on the mount. 2 Tilt the device forward. Removing the Mount from the Suction Cup 1 Turn the device mount to the right or left. 2 Apply pressure until the socket on the mount releases the ball on the suction cup. Appendix 11