Gateway 7400 System Manual (PDF Version) - Page 40

Replace the bezel. See, original positions.

Get Gateway 7400 PDF manuals and user guides View all Gateway 7400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

7 Disengage the rail locking tabs by pressing in on both front rail extensions, then move the drive slightly out of the bay by pushing on the back of the drive. Pull the drive out of the chassis. 8 Remove the rails on both sides of the drive and snap them onto the new drive in the same positions. Make sure the front rail extensions are towards the front of the drive. Important The rails on the 3.5-inch diskette drive are different from those on the hard drive and the CD drive. Make sure you install the correct rails on each drive. 9 Set the drive jumpers to the appropriate settings (refer to your drive documentation for jumper settings.) 10 Align the rails with the diskette drive bay, then slide the drive into the bay until the locking tabs snap into place. 11 Connect the power and data cables, making sure the cables are in their original positions. 12 Replace the bezel. (See "Replacing the bezel" on page 28.) 13 Close the case. (See "Closing the case" on page 27.) 14 Reconnect the power cord, the modem cord, and all other external peripheral devices, then turn on the system. 32 Replacing and Adding System Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
32
Replacing and Adding System Components
7
Disengage the rail locking tabs by pressing in on both front rail
extensions, then move the drive slightly out of the bay by pushing on
the back of the drive. Pull the drive out of the chassis.
8
Remove the rails on both sides of the drive and snap them onto the new
drive in the same positions. Make sure the front rail extensions are
towards the front of the drive.
9
Set the drive jumpers to the appropriate settings (refer to your drive
documentation for jumper settings.)
10
Align the rails with the diskette drive bay, then slide the drive into the
bay until the locking tabs snap into place.
11
Connect the power and data cables, making sure the cables are in their
original positions.
12
Replace the bezel. (See
“
Replacing the bezel
”
on page 28.)
13
Close the case. (See
“
Closing the case
”
on page 27.)
14
Reconnect the power cord, the modem cord, and all other external
peripheral devices, then turn on the system.
Important
The rails on the 3.5-inch diskette drive are different from
those on the hard drive and the CD drive. Make sure you
install the correct rails on each drive.