Gateway E-9425R Gateway E-9425R Server User Guide - Page 36

Closing the server case

Get Gateway E-9425R PDF manuals and user guides View all Gateway E-9425R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

CHAPTER 4: Installing Components 7 Press down the two blue retaining clips (1) on the sides of the top front cover, then slide the top front cover back (2) and lift it off the server. Caution For correct cooling and air flow, always reinstall the top covers before you turn on the server. Operating the server without the covers in place will cause the server to overheat. Closing the server case Important The hard drive carriers shown in these illustrations may look different than the actual hard drive carriers in your server. To close the server case: 1 Make sure that all of the internal cables are arranged inside the case so they will not be pinched when you close the case. 2 Place the front top cover on the case and slide the cover forward, then lift the two blue retaining clips into place. 3 Place the rear top cover (1) on the case, then slide it forward until it clicks into place. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
CHAPTER 4: Installing Components
30
7
Press down the two blue retaining clips (1) on the sides of the top front cover, then slide
the top front cover back (2) and lift it off the server.
Closing the server case
To close the server case:
1
Make sure that all of the internal cables are arranged inside the case so they will not be
pinched when you close the case.
2
Place the front top cover on the case and slide the cover forward, then lift the two blue
retaining clips into place.
3
Place the rear top cover (1) on the case, then slide it forward until it clicks into place.
Caution
For correct cooling and air flow, always reinstall the top covers before you
turn on the server. Operating the server without the covers in place will cause the
server to overheat.
Important
The hard drive carriers shown in these illustrations may look different than the actual
hard drive carriers in your server.