Gateway E-9425R Gateway E-9425R Server User Guide - Page 45

Installing and removing PCI expansion cards, Removing and installing the PCI riser assembly, a riser

Get Gateway E-9425R PDF manuals and user guides View all Gateway E-9425R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

www.gateway.com Installing and removing PCI expansion cards Caution Always operate your server with the PCI riser assembly in place. The PCI riser assembly is important for correct airflow within the server. Operating the server without the PCI riser assembly in place could result in overheating and possible data loss or equipment damage. The system board provides one 280-pin PCI-X/PCI-E x8 expansion slot and one PCI-E x8 expansion slot. The PCI-X/PCI-E x8 expansion slot (on the left side when viewed from the front of the server) can support one PCI-X 100MHz or one PCI-E x8 using the riser card. The PCI-E expansion slot (on the right side when viewed from the front of the server) can support one PCI-E x8 using the riser card. The riser card comes with the system package. Removing and installing the PCI riser assembly, a riser, or PCI card Caution The PCI riser assembly and individual PCI expansion cards are not hot-swappable. Before installing or removing any part of the assembly, make sure that power is turned off and the power cords are unplugged. To remove and reinstall the PCI riser assembly: 1 Follow the instructions in "Preventing static electricity discharge" on page 28. Make sure that you turn off the server, then unplug the power cord(s) and all other cables connected to the server. 2 Follow the instructions in "Opening the server case" on page 29. 3 If you are replacing a card, disconnect any cables that are attached to the old card. 4 Loosen the two thumbscrews (1) at the back of the chassis, push the release clips (2) in the direction shown in the illustration, then lift the assembly (3) out of the chassis. Caution Do not touch the contacts on the bottom part of the expansion card. Touching the contacts can cause electrostatic damage to the card. 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
www.gateway.com
39
Installing and removing PCI expansion cards
The system board provides one 280-pin PCI-X/PCI-E x8 expansion slot and one PCI-E x8 expansion
slot. The PCI-X/PCI-E x8 expansion slot (on the left side when viewed from the front of the server)
can support one PCI-X 100MHz or one PCI-E x8 using the riser card. The PCI-E expansion slot (on
the right side when viewed from the front of the server) can support one PCI-E x8 using the riser
card. The riser card comes with the system package.
Removing and installing the PCI riser assembly, a riser, or PCI card
To remove and reinstall the PCI riser assembly:
1
Follow the instructions in
“Preventing static electricity discharge” on page 28
. Make sure that
you turn off the server, then unplug the power cord(s) and all other cables connected to the
server.
2
Follow the instructions in
“Opening the server case” on page 29
.
3
If you are replacing a card, disconnect any cables that are attached to the old card.
4
Loosen the two thumbscrews (1) at the back of the chassis, push the release clips (2) in the
direction shown in the illustration, then lift the assembly (3) out of the chassis.
Caution
Always operate your server with the PCI riser assembly in place. The PCI riser
assembly is important for correct airflow within the server. Operating the server without
the PCI riser assembly in place could result in overheating and possible data loss or
equipment damage.
Caution
The PCI riser assembly and individual PCI expansion cards are not hot-swappable.
Before installing or removing any part of the assembly, make sure that power is turned off
and the power cords are unplugged.
Caution
Do not touch the contacts on the bottom part of the expansion card. Touching
the contacts can cause electrostatic damage to the card.