Gateway GM5407E 8512041 - Gateway Hardware Reference Guide (5-bay uATX Case) - Page 57

Replacing the system board

Page 57 highlights

www.gateway.com Replacing the system board To replace the system board: 1 Remove the side panel by following the instructions in "Removing the side panel" on page 31. 2 Remove all expansion cards by following the directions in "Adding or replacing an expansion card" on page 47. 3 Remove all memory modules by following the directions in "Installing memory" on page 37. 4 Disconnect all the power and data cables from the system board, noting their locations and orientation. (You will reconnect the cables after you install the new board.) Tip You can label each cable with tape to make it easier to re-connect them later. 5 Remove the four screws that secure the power supply to your computer, then slide it out of your computer. 6 Remove the seven system board screws. Screws Screws 7 Lift the system board up and out of the case. 8 Align the new system board on the screw holes in the case, then secure it into the case with the screws. 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132

www.gateway.com
51
Replacing the system board
To replace the system board:
1
Remove the side panel by following the instructions in
“Removing the side panel” on page 31
.
2
Remove all expansion cards by following the directions
in
“Adding or replacing an expansion card” on page 47
.
3
Remove all memory modules by following the directions
in
“Installing memory” on page 37
.
4
Disconnect all the power and data cables from the
system board, noting their locations and orientation.
(You will reconnect the cables after you install the new
board.)
5
Remove the four screws that secure the power supply
to your computer, then slide it out of your computer.
6
Remove the seven system board screws.
7
Lift the system board up and out of the case.
8
Align the new system board on the screw holes in the
case, then secure it into the case with the screws.
Tip
You can label each cable with tape to make it easier to re-connect
them later.
Screws
Screws