Home » GE Manuals » Home Security » GE 60-803-04 » Manual Viewer

GE 60-803-04 Installation Instructions

GE 60-803-04 - Security Superbus 2000 LCD Alphanumeric Touchpad Manual

UPC - 046188088645

View all GE 60-803-04 manuals

Add to My Manuals
Save this manual to your list of manuals

GE 60-803-04 manual content summary:

GE 60-803-04 | Installation Instructions - Page 1
ITI Part No. 60-803 & 60-809 Document Number: 466-1632 Rev. B September 2000 Product Summary Installation Instructions Installation Guidelines The ITI® SuperBus 2000 2 x 20 LCD (liquid crystal display) Alphanumeric Touchpad gives you complete on-site system programming and operation control of a
GE 60-803-04 | Installation Instructions - Page 2
on all sides of the back-plate. 3. Drill holes and insert appropriate anchors. 4. Secure the back-plate to the wall with included screws. 5. Cut a hole in the wall . Find your panel in the next section for specific wiring instructions. LOOSEN BOTTOM SCREWS (X2) 3101G03B.DSF Figure 1. Touchpad
GE 60-803-04 | Installation Instructions - Page 3
in UltraGard systems). Note The optional touchpad hardwire input must be added to panel memory. See the UltraGard panel Installation Instructions or Reference Manual for setting the configuration. 3. Insert the touchpad wiring harness connector onto the pins located on the rear of the unit
GE 60-803-04 | Installation Instructions - Page 4
change partition assignment please see specific panel Installation Instructions. All partitions must be disarmed before entering RUN. 5. Turn on the panel power switch. 6. Put the touchpad into the manual configuration mode by pressing and holding the touchpad D and 6 buttons until the display
GE 60-803-04 | Installation Instructions - Page 5
wiring harness to one new touchpad. 12. Put the new touchpad into the manual configuration mode by pressing and holding the touchpad D and 6 buttons until the touchpad does not display the current system status, see "Troubleshooting." Additional Touchpads 1. Verify that all wiring between the panel
GE 60-803-04 | Installation Instructions - Page 6
," see "Troubleshooting." Deleting Touchpads/Unit Numbers from Panel Memory Please see the specific Installation Instructions for information on deleting touchpads/unit numbers. Adjusting Contrast and Backlighting Please see the specific panel Installation Instructions or User's Manual for more
GE 60-803-04 | Installation Instructions - Page 7
panels. Table 3: UltraGard Troubleshooting Problem All touchpads display 1. 1 - OFF but they don't work or won't enter program mode. 2. The touchpad displays the 1. message BUS FAIL UNIT N (N = unit number of failed bus device). 2. 3. The panel reports a trouble 1. condition on the
GE 60-803-04 | Installation Instructions - Page 8
60-803-04 Concord, Concord Express 60-809-03 Custom Concord Versions 60-809-03-SEC Security Pro® UltraGard and Custom Versions 60-803-03 UltraGard and Custom Versions 60-803 in accordance with the instruction manual, may cause harmful . ITI, SuperBus, Advent, UltraGard, and Security Pro

Section	Page
Product Summary	1
SuperBus 2000 Panels vs. SuperBus Panels	1
Installation Guidelines	1
Table 1: Maximum Bus Devices Per Panel	1
Panel	1
Maximum Bus Devices	1
Table 2. Hardwire Input Wire Length Limits	1
Gauge	1
Max. Wire Length	1
The following must be observed in UL installations	2
Tools Needed	2
Installation	2
To mount the touchpad on a wall:	2
1. Separate the mounting bracket from the back-plate by loosening the two bottom screws and unlat...	2
2. Place the back-plate on the wall and mark the four mounting holes and the wire access hole (se...	2
3. Drill holes and insert appropriate anchors.	2
4. Secure the back-plate to the wall with included screws.	2
5. Cut a hole in the wall where the wire access hole was marked to pull your cable through.	2
Figure 1. Touchpad Mounting Slots	2
To mount the touchpad in a gang box:	2
1. Separate the mounting bracket from the back-plate by loosening the two bottom screws and unlat...	2
2. Line up the gang box mounting holes with the holes on the gang box (see Figure 2).	2
3. Secure the back-plate to the gang box with panhead screws.	2
Figure 2. Back-Plate and Mounting Holes	2
Wiring	2
Before You Begin	2
1. Disconnect the panel AC power transformer and backup battery (turn off power switch on UltraGa...	2
2. Run a 4-conductor, 22-gauge wire cable from the panel to the touchpad location.	2
3. Splice the 4-conductor cable wires to the matching colored wires located on the touchpad wirin...	2
Wiring Panels	3
UltraGard Panels	3
1. Connect the touchpad wiring to the panel terminals as shown in Figure 3. Wire multiple touchpa...	3
2. If desired, connect an optional hardwire switch to the yellow touchpad wires as shown in Figur...	3
3. Insert the touchpad wiring harness connector onto the pins located on the rear of the unit. Ma...	3
Figure 3. Wiring the Touchpad to UltraGard Panels	3
Concord/Concord Express Panels	3
1. Connect the touchpad wiring to the panel terminals as shown in Figure 4. Wire multiple touchpa...	3
2. If desired, connect an optional hardwire switch to the yellow touchpad wires as shown in Figur...	3
3. Insert the touchpad wiring harness connector onto the pins located on the rear of the unit. Ma...	3
Figure 4. Wiring the Touchpad to Concord and Concord Express Panels	3
Advent Panels	3
1. Splice the touchpad wiring to the panel SuperBus wiring harness as shown in Figure 5. Wire mul...	3
2. If desired, connect an optional hardwire switch to the yellow wires on the touchpad wiring har...	3
3. Insert the touchpad wiring harness connector onto the pins located on the rear of the unit. Ma...	4
Figure 5. Wiring the Touchpad to Advent Panels	4
Mounting the Touchpad	4
1. Align the slots on the touchpad with the slots on the back-plate. Insert the mounting tabs int...	4
2. Tighten the two bottom screws.	4
Setting Touchpad Unit Numbers	4
Guidelines for Assigning Alphanumeric Touchpad Unit Numbers (Concord panels with software version...	4
Power Up and Bus Communication	4
Powering Up UltraGard Panels	4
First Touchpad	4
1. Disconnect all bus device wiring from the panel except for the touchpad location closest to th...	4
2. Verify that all wiring at the panel and touchpad wiring harness is correct.	4
3. With the panel power switch off, connect the panel battery and plug in the panel AC power tran...	4
4. Set the panel RUN/PROGRAM switch to RUN.	4
5. Turn on the panel power switch.	4
6. Put the touchpad into the manual configuration mode by pressing and holding the touchpad D and...	4
7. Set the panel RUN/PROGRAM switch to PROGRAM and the display should read program mode.	4
8. Verify correct operation by pressing STATUS or BYPASS. The display should show a different men...	4
1. Disconnect the panel AC power transformer, backup battery, and turn off the power switch.	5
2. Connect all bus device wiring to the panel (including the wiring that was disconnected in step...	5
3. Verify that all wiring at the panel and at the added touchpad wiring harnesses are correct (bu...	5
4. Apply power to the panel (turn on the power switch).	5
5. Set the RUN/PROGRAM switch to PROGRAM. Existing (previously installed) touchpad(s) display pro...	5
6. At an existing touchpad, press BYPASS or STATUS until the display shows touchpad options.	5
7. Press COMMAND and the display shows unit number.	5
8. Press COMMAND; existing touchpads will display DA 00N (where N is the unit number 0–7). Make a...	5
9. Check the unit numbers of all other existing touchpads and write them down.	5
10. Check the unit number DIP switches on other bus devices (ESM, HIM, etc.) and make a note of t...	5
11. Connect the wiring harness to one new touchpad.	5
12. Put the new touchpad into the manual configuration mode by pressing and holding the touchpad ...	5
13. Press BYPASS and the display shows enter _.	5
14. Enter a unit number different from that of the existing touchpads and any other bus devices i...	5
15. Press BYPASS then STATUS to lock in and display the new unit number for the touchpad.	5
16. Disconnect this touchpad and repeat steps 11 through 16 for any other new alphanumeric touchp...	5
17. After assigning unit numbers to all the new touchpads, connect each touchpad to its respectiv...	5
18. Set the RUN/PROGRAM switch to RUN. All touchpads should display 1 - off.	5
19. Set the RUN/PROGRAM switch to PROGRAM so the panel can learn all bus device unit numbers. All...	5
20. Set the RUN/PROGRAM switch to RUN.	5
21. At each touchpad, verify correct operation by pressing STATUS. The display should show the cu...	5
Powering up Concord Panels with Software Version 2.0 or Newer and Concord Express Panels	5
1. Verify that all wiring between the panel and touchpad is correct.	5
2. Connect the panel battery and plug in the panel transformer. Alphanumeric touchpads show “SCAN...	5
3. Verify correct operation by pressing Ç. The display should show the current system status.	5
Powering up Concord Panels with Software Versions 1.0–1.6	5
First Touchpad	5
1. Verify that all wiring between the panel and touchpad is correct.	5
2. Check the unit number DIP switches on all other bus devices (ESM, HIM, etc.) and make note of ...	5
3. Connect the panel battery and plug in the panel transformer. Alphanumeric touchpads show “SCAN...	5
4. Verify correct operation by pressing Ç. The display should show the current system status.	5
Additional Touchpads	5
1. Verify that all wiring between the panel and touchpad is correct.	5
2. Check the unit number DIP switches on other bus devices (ESM, HIM, etc.) and make a note of th...	5
3. Connect the panel battery and plug in the panel transformer. Alphanumeric touchpads show “SCAN...	5
4. At a touchpad, press and hold the D and 6 buttons (together) for at least 2 seconds. The displ...	6
5. Press É. The display shows ENTER _.	6
6. Enter an unused three digit unit number (000 – 015), then press É. The display shows DA n, whe...	6
7. Press Ç to exit from the configuration mode.	6
8. Repeat steps 4–8 for all connected alphanumeric touchpads.	6
9. Force the panel to scan bus devices.	6
10. Exit the program mode. The touchpad and all other bus devices should operate correctly and an...	6
11. Verify correct operation by pressing Ç. The display should show the current system status.	6
Powering Up Advent Panels	6
New Installations	6
1. Verify that all wiring between the panel and touchpad is correct.	6
2. Connect the panel battery and plug in the panel transformer. The alphanumeric touchpad should ...	6
Existing Installations	6
1. Verify that all wiring between the panel and touchpad is correct.	6
2. Connect the panel battery and plug in the panel transformer.	6
3. At an existing touchpad, press 8 to select SYSTEM MENU.	6
4. Press 0 to select ENTER PROGRAM MODE.	6
5. Enter your install access code (0123 is default).	6
6. Enter item number 48001 to add bus devices. All installed devices are automatically added (lea...	6
7. Press Ç once to exit program mode.	6
8. New alphanumeric touchpads should display “Security is Off,” while existing touchpads will dis...	6
Deleting Touchpads/Unit Numbers from Panel Memory	6
Adjusting Contrast and Backlighting	6
Testing	6
Panel Programming	6
Troubleshooting	7
Table 3: UltraGard Troubleshooting	7
Problem	7
Action/Solution	7
1. Disconnect all touchpads except the original. Set the panel mode switch to PROGRAM, enter the ...	7
2. Assign a different unit number to each touchpad using the procedure outlined in this document.	7
1. Turn off the panel power switch. Check the wiring at all bus devices and correct where necessary.	7
2. Assign a different unit number to each touchpad using the procedure in this document.	7
3. Set the panel mode switch to PROGRAM then back to RUN.	7
1. Change the unit number on the new bus device to an unused unit number. Turn power OFF then ON....	7
2. Turn off the panel power switch. Check and correct the touchpad wiring.	7
3. The panel must learn the hardwire loops again when a touchpad unit number is changed.	7
Table 4: Concord and Concord Express Troubleshooting	7
Problem	7
Action/Solution	7
1. Check for correct wiring connections at the touchpad and panel terminals.	7
2. Make sure the panel battery is connected correctly and that the panel transformer is plugged in.	7
3. Make sure the panel transformer is not plugged into an electrical outlet controlled by a switc...	7
1. Check the touchpad display contrast setting. It may be set to 0 (no display).	7
1. Check for correct bus wiring connections (green and white wires) at the touchpad and panel ter...	7
2. Make sure the touchpad unit number is set to a number different from all other bus device unit...	7
Table 5: Advent Troubleshooting	7
Problem	7
Action/Solution	7
1. Check that the panel is not in the program mode of operation.	7
1. Check that the wiring connector is plugged into the back of the touchpad.	7
2. Check for incorrect wiring, opens, or shorts.	7
3. Check panel power.	7
4. From another touchpad enter program mode and verify touchpad is enrolled.	7
1. Perform the procedure for “Existing Installations” under the section “Powering up Advent Panel...	7
Specifications	8
Touchpad Part No.	8
Compatible Panel(s)	8
Notices	8

Match case Limit results 1 per page

SuperBus® 2000 2 x 20 LCD Alphanumeric Touchpad

Installation Instructions

Product Summary

The ITI

SuperBus 2000 2 x 20 LCD (liquid crystal dis-

play) Alphanumeric Touchpad gives you complete on-site

system programming and operation control of a compatible

security system (see the section “Specifications”).

A two-line, 40-character display provides visual system

status messages. The display identifies any programmed

location, allowing the user to determine where an alarm,

trouble, or open-sensor condition exists.

Other features include:

Touchpad buttons that light up after the first button

press and remain lit until about 15 seconds after the last

button press.

Adjustable display contrast and backlighting.

Built-in hardwire input (can be supervised with EOL

resistor in SuperBus 2000 panels).

Built-in door, which covers right-side buttons (60-809

only).

SuperBus 2000 Panels

vs.

SuperBus Panels

SuperBus 2000 panels assign module unit numbers

automatically when the panel is powered up. This

eliminates manually setting unit numbers and the chance of

identical unit number conflicts.

SuperBus 2000 Panels

Advent

Concord (software versions 2.0 and newer)

Concord Express

SuperBus panels communicate with SuperBus 2000

modules but require the module unit number to be set

manually. Touchpads automatically default to unit number

001.

SuperBus Panels

UltraGard

Concord (software versions 1.0–1.6)

Installation Guidelines

For the maximum number of bus devices and

touchpads per panel see Table 1.

Do not exceed the total panel output power when using

panel power for bus devices, touchpads, and hardwired

sensors that require it (see specific panel

Installation

Instructions

Maximum current draw from the touchpad is 120 mA.

Minimum current draw from the touchpad when the

panel is operating only on backup battery is 15 mA.

Mount the touchpad in an environmentally controlled

area (32° to 140° F) (0° to 60° C).

When using the optional touchpad hardwire input, use

only shielded wire (22-gauge or larger), and do not

exceed the maximum wire length limits in Table 2

between the touchpad and detection device.

Note

Shield wire must be connected to earth ground.

When mounting the touchpad back-plate, allow a 1-

inch clearance on all sides since the touchpad is larger

than the back-plate.

Use 4-conductor, 22-gauge or larger stranded wire from

the touchpad to the control panel.

Follow the wire length limits outlined in the specific

panel

Installation Instructions

between the touchpad

and control panel.

Table 1: Maximum Bus Devices Per Panel

Panel

Maximum Bus

Devices

Advent

UltraGard

Concord

Concord Express

Table 2. Hardwire Input Wire Length Limits

Gauge

Max. Wire

Length

18 (shielded)

1000 Feet

22 (shielded)

350 Feet

±²³´µ¶²·

¸¹ººº

¹¸»¸¹º¸¼½¾

¿À³ÁÂÃ²Ä´µÅÆ¸

ÇÈ²ÆÁ³ÂÉ

Document Number: 466-1632 Rev. B

September 2000

ITI Part No. 60-803 & 60-809