GE AJCQ12DCD Use and Care Manual - Page 19

Measure, Cut And Install Filler, Panels, The Angles.

Get GE AJCQ12DCD PDF manuals and user guides
UPC - 084691175377
View all GE AJCQ12DCD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Installation Instructions 6 MEASURE, CUT AND INSTALL FILLER PANELS A Measure from the edge of the panel marks (see Prepare the Window) to the inside of the window track on each side (A and B). Sill Window track Outside A Left side 133⁄8″ Inside 133⁄8″ Width of the air conditioner (panel marks) B Right side B Mark the A and B measurements on each side of the filler panel board. Cut the panels and discard the center piece. Note position of the notches. Gasket Angle Angle Gasket Panel Tab Type C (painted screws) D Install the panels in the window. Place the spring clips 3″ from the top and the bottom. Squeeze and push the clips to fit in the window track and the tab into the sill support. B A 3″ Right Left side side Filler Panels Cut panels and discard center piece (holes are on the left) (holes are on the right) C Put together the panel assemblies. Remove the paper backing from the case-side gasket and attach it to the angle. Push a pencil point through the gaskets to locate the holes in the angles. Hook the tab into the sill support 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Installation Instructions
19
MEASURE, CUT AND INSTALL FILLER
PANELS
Measure from the edge of the panel marks
(see Prepare the Window) to the
inside of the
window track
on each side
(A and B)
.
Mark the
A
and
B
measurements on each side
of the filler panel board. Cut the panels and discard
the center piece. Note position of the notches.
Put together the panel assemblies. Remove
the paper backing from the case-side gasket
and attach it to the angle. Push a pencil point
through the gaskets to locate the holes in
the angles.
Install the panels in the window. Place the spring clips
3
″
from the top and the bottom. Squeeze and push
the clips to fit in the window track and the tab into
the sill support.
6
A
B
C
D
Sill
A
Window track
Width of the air
conditioner
(panel marks)
Left side
B
Right side
13
3
±
8
″
13
3
±
8
″
Filler Panels
Cut panels
and discard
center piece
B
Right
side
A
Left side
(holes are on the left)
(holes are on the right)
Gasket
Gasket
Angle
Panel
Tab
Type C
(painted
screws)
Angle
Hook the tab into
the sill support
3
″
Inside
Outside