GE APE08AK Owners Manual - Page 14
Possible, Ca.se - troubleshooting
UPC - 084691160175
View all GE APE08AK manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 14 highlights
Troubleshootingtips... Save time and money! PossCibale.se, What To Do E4appears in the display Water bucket is full or not installed correctly. • Remoxe, empty and replace the water bucket. See the Usingthe Wate'rBucket section and the [nstallation [nstructions ill this manual. "HEAT"modeN selected butunitdoesnotheat Airconditioner does notstart Water bucket was removed while unit was operating. If you have a Cool only model, heat settings will not be active on your model. The air conditioner is unplugged, • Replace the water bucket. See the Using the Water Buckotsection. NOTER; eplace the water bucket immediately after emptying it to catch _l]l} collde/ls_ltioll which may COllthltle to _lCCtlll/tl]_lte. • Set the unit to AUTO,COOLD, RYer FANmode. HEArmode is not a\ aJlable and will not operate on cool (.fly models. • Make Stlre the air conditioner into the outlet. plug is pushed coml)letely Air conditioner has stopped running Airconditionedroesnot cool as it should Ak conditioner freezingup The remote control N not working Unit does not work after pressingthePowerpad Noiseor vibration Tbrheeakefurse isistrbiplopwedn,/circuit Power failure. The current interrupter device is tripped. The remote control is not working, Power interruption or power failure occurred, Sleepmode or the _mer Off pad has turned off the air conditioner. Airflow is restricted. The temp control may not be set correctly. The air filter is dirty. The room may have been hot. Cooling coils have iced up. Ice blocks the airflow and stops the air conditioner from cooling the room. The batteries are inserted incorrectly, The batteries may be dead. The remote control is too far from the air conditioner. An object, such as furniture or a towel, is blocking the signal. The water bucket is full or the water bucket is not properly installed. The floor is not level. • Cthheeckfuse thoer hroetslseet thfie_seb/rceirackuehr. breaker box and replace • [fa power l'hJ]ure occtn% ttlyH the air conditioner OFFX. _lle. p()wer is rest(wed, wait 3 rain utes to restart the air c(nlditi(mer to prexent tripping of tile compressor oxerloa(1. • Press the RESETbutton h)cated on the power cord plug. • If the RESETbutton will not stay engaged, discontinue use of the air conditioner and contact a qualified service technician. • Try operating the control on the unit. See The remote control is not workingbell);v. • _'\]Jen the p()wer I•s rest(n'e(t, wait' 9.>. mm' utes to restart the air conditioner to pre',ent tripping of the compressor oxerload. Touch the Powerpad and reset the controls to the desired settings. • Set the air conditioner to the desh'ed setting. • Make Stl/'e there are no curtains, blinds or ftl/'I/ittlFe blocking the inlets l/)cated on the left and rear skles of the air c(m(titi(mer. Make sure there are at least 12" of space on all sides of the unit. _']_lke StlFe airflow through the \ent exhaust is not blocked. •/n COOLmode, touch tile TempDecrease• pad. • Clean tile filter at least exel)" 3(1 days. See tile Care and cleaning section. • _\]Jen the air conditioner is thst turned on, you need to :dlow time Ii)l" the l'OOIll [o cool dowlL • See "Ak conditioner freezing up" bel ( )w. • Tile air conditioner will dei}'ost and return to operation on its ()_r]_. • To deft'( )st the air conditioner more quJckl}, select the COOL mode and HIGHIimand set tile thermostat to a higher temperature. • Check the position of the batteries. The)" should be inserted in the opposite (+) and (-) direction. • Replace tile batteries. • Operate the remote control closer to the air conditionec • Remove the ob.iect, • Remove water fi'om tile water bucket and push the water bucket back ill place. • Place unit ()n a fiat, lex el surihce. 14