GE GBC12IAXLSS Use and Care Manual - Page 14

Hang The Fresh Food Door, Install Door Cap Cont.

Get GE GBC12IAXLSS PDF manuals and user guides
UPC - 084691176459
View all GE GBC12IAXLSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Installation Instructions REVERSING THE DOOR SWING (cont.) 11 TRANSFER FRESH FOOD DOORSTOP AND HOLE INSERTS A Remove the fresh food doorstop from the bottom right side of the door. B Remove the hole insert from the bottom right side of the fresh food door. C Install the fresh food doorstop to the bottom left side of the door. D Install the hole insert on the bottom left side of the fresh food door. 13 INSTALL DOOR CAP (CONT.) C Place the top cap onto the top of the fresh food drawer. D Using the screws removed earlier, secure the top cap onto the fresh food door, covering the end of the hinge. Screw Screw Doorstop Hole Insert 12 HANG THE FRESH FOOD DOOR A Place the fresh food door onto the center hinge over the pin. B While holding the door in place, raise the top hinge and insert the top pin into the hole in the door. Swing door shut. C Align the freezer door with the fresh food door so the gap between the doors is even. D Tighten the top hinge screws by turning them until snug. Then turn the screws a minimum of 1/2 turn using both hands. 13 INSTALL DOOR CAP A Remove the insert on the bottom of the door cap with a thin-blade screwdriver. 14 INSTALL HINGE COVER AND ELECTRONICS BOX COVER A Remove the tab from the left side of the hinge cover. B Install the tab into the right side of the hinge cover. C Lift up the electronics box cover and place the middle portion of the hinge cover over the wire harnesses and under the edge of the electronics box cover. NOTE: Be careful not to pinch the wiring. D Using the screws removed earlier, attach the hinge cover to the cabinet. E Using the screws removed earlier, attach the electronics box cover to the cabinet. Screws Electronics Box Cover Screws B Install the insert into the right side of the door cap. Hinge Cover 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Installation Instructions
REVERSING THE DOOR SWING
(cont.)
TRANSFER FRESH FOOD DOORSTOP
AND HOLE INSERTS
Remove the fresh food doorstop from
the bottom right side of the door.
Remove the hole insert from the bottom right
side of the fresh food door.
Install the fresh food doorstop to the bottom
left side of the door.
Install the hole insert on the bottom left side
of the fresh food door.
11
A
B
C
D
HANG THE FRESH FOOD DOOR
Place the fresh food door onto the center hinge
over the pin.
While holding the door in place, raise the top
hinge and insert the top pin into the hole in
the door. Swing door shut.
Align the freezer door with the fresh food door
so the gap between the doors is even.
Tighten the top hinge screws by turning them
until snug. Then turn the screws a minimum
of 1/2 turn using both hands.
12
A
B
C
D
INSTALL DOOR CAP (CONT.)
Place the top cap onto the top of the fresh food
drawer.
Using the screws removed earlier, secure
the top cap onto the fresh food door, covering
the end of the hinge.
13
C
D
Screw
Screw
INSTALL HINGE COVER AND
ELECTRONICS BOX COVER
Remove the tab from the left side of the hinge
cover.
Install the tab into the right side of the hinge
cover.
Lift up the electronics box cover and place
the middle portion of the hinge cover over
the wire harnesses and under the edge
of the electronics box cover.
NOTE:
Be careful
not to pinch the wiring.
Using the screws removed earlier, attach
the hinge cover to the cabinet.
Using the screws removed earlier, attach
the electronics box cover to the cabinet.
14
A
B
C
D
E
INSTALL DOOR CAP
Remove the insert on the bottom of the door
cap with a thin-blade screwdriver.
Install the insert into the right side
of the door cap.
13
A
B
Electronics
Box Cover
Screws
Screws
Hinge
Cover
14
Hole
Insert
Doorstop