GE JGBP32SENSS Owners Manual - Page 26

Burner Caps and Heads, Burner caps, After cleaning, Replacement, On some models

Get GE JGBP32SENSS - 30inch Gas Range PDF manuals and user guides
UPC - 084691187349
View all GE JGBP32SENSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Consumer Support Troubleshooting Tips Installation Instructions Operating Instructions Safety Instructions Care and cleaning of the range. Use a sewing needle or twist-tie to unclog the small hole in the burner head. Burner Caps and Heads NOTE: Before removing the burner caps and heads, remember their size and location. Replace them in the same location after cleaning. Burner caps Lift off when cool. Wash burner caps in hot, soapy water and rinse with clean water. You may scour with a plastic scouring pad to remove burned-on food particles. Burner heads For proper ignition, make sure the small hole in the section that fits over the electrode is kept open. A sewing needle or wire twist-tie works well to unclog it. The slits in the burner heads must be kept clean at all times for an even, unhampered flame. Clogged or dirty burner ports or electrodes will not allow the burner to operate properly. Any spill on or around an electrode must be carefully cleaned. Take care to not hit an electrode with anything hard or it could be damaged. You should clean the burner caps and burner heads routinely, especially after bad spillovers, which could clog the openings in the burner heads. Lift off when cool. To remove burned-on food, soak the burner heads in a solution of mild liquid detergent and hot water for 20-30 minutes. For more stubborn stains, use a toothbrush. After cleaning Before putting the burner caps and heads back, shake out excess water and then dry them thoroughly by setting in a warm oven for 30 minutes. NOTE: Do not use steel wool or scouring powders to clean the burners. Replacement Replace burner heads over the electrodes on the cooktop, in the correct locations according to their size. On some models: Medium head and cap Small head and cap Large head and cap Front of range On some models: Medium head and cap Large head and cap Small head and cap Front of range Medium head and cap Large head and cap Make sure the slot in the burner head is positioned over the electrode. Replace the matching size caps onto the heads. Make sure that the heads and caps are replaced in the correct locations. NOTE: On some models, the burners are all the same size and power. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Operating Instructions
Safety Instructions
Installation Instructions
Troubleshooting Tips
Consumer Support
26
Burner Caps and Heads
Burner caps
Lift off when cool. Wash burner caps
in hot, soapy water and rinse with clean
water. You may scour with a plastic scouring
pad to remove burned-on food particles.
Burner heads
For proper ignition, make sure the
small hole in the section that fits over the
electrode is kept open. A sewing needle
or wire twist-tie works well to unclog it.
The slits in the burner heads must be kept clean
at all times for an even, unhampered flame.
Clogged or dirty burner ports or electrodes
will not allow the burner to operate properly.
Any spill on or around an electrode must
be carefully cleaned. Take care to not hit an
electrode with anything hard or it could
be damaged.
You should clean the burner caps and
burner heads routinely, especially after bad
spillovers, which could clog the openings
in the burner heads. Lift off when cool.
To remove burned-on food, soak the
burner heads in a solution of mild liquid
detergent and hot water for 20–30 minutes.
For more stubborn stains, use a toothbrush.
After cleaning
Before putting the burner caps and heads
back, shake out excess water and then dry
them thoroughly by setting in a warm oven
for 30 minutes.
NOTE:
Do not use steel wool or scouring powders
to clean the burners.
Replacement
Replace burner heads over the electrodes
on the cooktop, in the correct locations
according to their size.
On some models:
On some models:
Make sure the slot in the burner head is
positioned over the electrode.
Replace the matching size caps onto the
heads.
Make sure that the heads and caps are
replaced in the correct locations.
NOTE:
On some models, the burners are all the
same size and power.
NOTE:
Before removing the burner caps
and heads, remember their size and location.
Replace them in the same location after
cleaning.
Medium head
and cap
Front of range
Large head
and cap
Small head
and cap
Large head
and cap
Care and cleaning of the range.
Use a sewing needle or twist-tie
to unclog the small hole in the
burner head.
Medium head
and cap
Front of range
Medium head
and cap
Small head
and cap
Large head
and cap