GE JVM3160RFSS Installation Instructions - Page 21

Adapting Blower For, Outside Back Exhaust, Use Top Cabinet Template, For Preparation Of Top, Cabinet - parts

Get GE JVM3160RFSS PDF manuals and user guides View all GE JVM3160RFSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Installation Instructions C2 ATTACH THE MOUNTING PLATE TO THE WALL cont 7RXVHWRJJOHEROWV Spacing for Toggles More Than Wall Thickness Mounting Plate Toggle Wings Toggle Bolt Bolt Wall End 3 Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate. NOTE: Before tightening toggle bolts and wood screw, make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet. CAUTION:%HFDUHIXOWRDYRLGSLQFKLQJ ILQJHUVEHWZHHQWKHEDFNRIWKHPRXQWLQJSODWHDQG the wall. 4 Tighten all bolts. Pull the plate away from the wall to help tighten the bolts. C3 USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit through. C4 ADAPTING BLOWER FOR OUTSIDE BACK EXHAUST 1 Remove the blower motor screws that holds the blower plate to the microwave oven. Slide the plate toward the back of the microwave and lift up to remove. Blower Motor Screws Blower Plate 2 Remove screw on the back of the unit. Screw 3 Carefully remove fan from cavity. Remove the wire from the notch at the bottom of the fan after it is removed from the cavity. 4 The fan needs to be turned 180 degrees to the right to be in the correct orientation, keeping the blower part of the fan where the air comes out at the top of the fan. The wire needs to be reinsterted into the cage housing once it has been oriented correctly. ‡ Read the instructions on the TOP CABINET TEMPLATE. ‡ Tape it underneath the top cabinet. ‡ Drill the holes, following the instructions on the TOP CABINET TEMPLATE. CAUTION::HDUVDIHW\JRJJOHVZKHQ GULOOLQJKROHVLQWKHFDELQHWERWWRP Fan Blades Wires Back of Microwave 5 Remove the knockout plates in the back of the unit with snips. Knockout Plates: Snip all 4 webs on each knockout panel and remove the metal knockouts for rear airflow. Please take care to remove any sharp edges created from removing Back of mircrowave the knockout plates. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
2
1
Remove the blower motor screws that holds the blower
plate to the microwave oven. Slide the plate toward the
back of the microwave and lift up to remove.
ADAPTING BLOWER FOR
OUTSIDE BACK EXHAUST
C4
Remove screw on the back of the unit.
21
USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
C3
Read the instructions on the TOP CABINET
TEMPLATE.
Tape it underneath the top cabinet.
Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.
CAUTION:
Wall
Mounting
Plate
Spacing for Toggles More
Than Wall Thickness
Toggle
Bolt
Toggle Wings
Bolt
End
Installation Instructions
You need to drill holes for the top support screws and
a hole large enough for the power cord to fit through.
Place the mounting plate against the wall and insert
the toggle wings into the holes in the wall to mount
the plate.
NOTE:
Before tightening toggle bolts and wood screw,
make sure the tabs on the mounting plate touch
the bottom of the cabinet when pushed flush against
the wall and that the plate is properly centered under
the cabinet.
CAUTION:
the wall.
Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
3
4
Blower Plate
Blower Motor Screws
The fan needs to be turned 180 degrees to the right
to be in the correct orientation, keeping the
blower
part of the fan where the air comes out at the top
of the fan.
The wire needs to be reinsterted into the
cage housing once it has been oriented correctly.
4
Back of Microwave
Fan Blades
Wires
3
ATTACH THE MOUNTING PLATE
TO THE WALL
cont
C2
Screw
Carefully remove fan from cavity. Remove the wire
from the notch at the bottom of the fan after it is
removed from the cavity.
5
Remove the knockout plates in the back of the unit
with snips.
Back of mircrowave
Knockout Plates:
Snip all 4 webs on
each knockout panel
and remove the metal
knockouts for rear airflow.
Please take care to
remove any sharp edges
created from removing
the knockout plates.