Gigabyte GA-6LXSG Manual - Page 26

FP_1 Front Panel Header, before connecting the cables.

Get Gigabyte GA-6LXSG PDF manuals and user guides View all Gigabyte GA-6LXSG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

15) FP_1 (Front Panel Header) Connect the power switch, reset switch, chassis intrusion switch/sensor and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables. 12 23 24 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Signal Name PWLED+ 5VSB NC NC PWLED- NC HD+ NC HD- (GND) NC PWB+ L1_LINK PWB+_GND L1_ACT RST_BTN+ SENSOR_SDA RST_BTN_GND SENSOR_SCL NC CASE_OPEN- NC L2_LINK NMI_SW- L2_ACT Definition Power LED Signal anode (+) 5V Stanndby Power No Pin No Connect Power LED Signal cathode(-) No Connect Hard Disk LED Signal anode (+) No Connect Hard Disk LED Signal cathode(-) No Connectthode(-) Power Button Signal anode (+) LAN1link LED Signal Power Button Signal cathode(-) LAN1 active LED Signal cathode(-) Reset button Signal anode (+) SMBus Data Signal Reset button Signal cathode(-) SMBus Clock Signal No Connect Chassis intrusion Signal cathode(-) No Connect LAN2 Link LED Signal cathode(-) NMI switch Signal cathode(-) LAN2 active LED Signal cathode(-) The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly. - 26 - Hardware Installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
- 26 -
Hardware Installation
The front panel design may differ by chassis. A front panel module mainly consists of power switch,
reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis
front panel module to this header, make sure the wire assignments and the pin assignments are
matched correctly.
15) FP_1 (Front Panel Header)
Connect the power switch, reset switch, chassis intrusion switch/sensor and system status indicator on
the chassis to this header according to the pin assignments below. Note the positive and negative pins
before connecting the cables.
1
2
23 24
Pin No.
Signal Name
Deļ¬nition
1
PWLED+
Power LED Signal anode (+)
2
5VSB
5V Stanndby Power
3
NC
No Pin
4
NC
No Connect
5
PWLED-
Power LED Signal cathode(-)
6
NC
No Connect
7
HD+
Hard Disk LED Signal anode (+)
8
NC
No Connect
9
HD- (GND)
Hard Disk LED Signal cathode(-)
10
NC
No Connectthode(-)
11
PWB+
Power Button Signal anode (+)
12
L1_LINK
LAN1link LED Signal
13
PWB+_GND
Power Button Signal cathode(-)
14
L1_ACT
LAN1 active LED Signal cathode(-)
15
RST_BTN+
Reset button Signal anode (+)
16
SENSOR_SDA
SMBus Data Signal
17
RST_BTN_GND
Reset button Signal cathode(-)
18
SENSOR_SCL
SMBus Clock Signal
19
NC
No Connect
20
CASE_OPEN-
Chassis intrusion Signal cathode(-)
21
NC
No Connect
22
L2_LINK
LAN2 Link LED Signal cathode(-)
23
NMI_SW-
NMI switch Signal cathode(-)
24
L2_ACT
LAN2 active LED Signal cathode(-)