Gigabyte GA-6LXSV Manual - Page 29

J_MEUPDATE/J_HDA_SDO1 ME Recover Jumpers, J_CLRCMOS Clearing CMOS Jumper

Get Gigabyte GA-6LXSV PDF manuals and user guides View all Gigabyte GA-6LXSV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

24) J_CLRCMOS (Clearing CMOS Jumper) Use this jumper to clear the CMOS values (e.g. date information and BIOS configurations) and reset the CMOS values to factory defaults. To clear the CMOS values, place a jumper cap on the two pins to temporarily short the two pins or use a metal object like a screwdriver to touch the two pins for a few seconds. 1 1-2 Close: Normal operation (Default setting) 1 2-3 Close: Clear CMOS data • Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS values. • After clearing the CMOS values and before turning on your computer, be sure to remove the jumper cap from the jumper. Failure to do so may cause damage to the motherboard. • After system restart, go to BIOS Setup Exit menu and load factory defaults (select Load Default Values) or manually configure the BIOS settings (refer to Chapter 2, "BIOS Setup," for BIOS configurations). 25/26) J_MEUPDATE/J_HDA_SDO1 (ME Recover Jumpers) J_HDA_SDO1 J_MEUPDATE J_MEUPDATE 1-2 Close: Normal operation (Default setting) 1 2-3 Close: ME recovery mode. 1 J_HDA_SDO_1 1-2 Close: ME recovery mode. 1 2-3 Close: Normal operation (Default setting) 1 - 29 - Hardware Installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
- 29 -
Hardware Installation
25/26)
J_MEUPDATE/J_HDA_SDO1 (ME Recover Jumpers)
1-2 Close: Normal operation (Default setting)
1-2 Close: ME recovery mode.
J_MEUPDATE
J_HDA_SDO_1
2-3 Close: ME recovery mode.
2-3 Close: Normal operation (Default setting)
1
1
1
1
24) J_CLRCMOS (Clearing CMOS Jumper)
Use this jumper to clear the CMOS values (e.g. date information and BIOS configurations) and reset
the CMOS values to factory defaults. To clear the CMOS values, place a jumper cap on the two pins to
temporarily short the two pins or use a metal object like a screwdriver to touch the two pins for a few
seconds.
1-2 Close: Normal operation (Default setting)
2-3 Close: Clear CMOS data
1
1
•
Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS
values.
•
After clearing the CMOS values and before turning on your computer, be sure to remove the jumper cap from
the jumper. Failure to do so may cause damage to the motherboard.
•
After system restart, go to BIOS Setup Exit menu and load factory defaults (select
Load Default Values
) or
manually
configure the BIOS settings (refer to Chapter 2, "BIOS Setup," for BIOS configurations).
J_MEUPDATE
J_HDA_SDO1