Gigabyte GA-M55S-S3 Manual - Page 73

Making a SATA Driver Disk

Get Gigabyte GA-M55S-S3 PDF manuals and user guides View all Gigabyte GA-M55S-S3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

English (4) Making a SATA Driver Disk To install operating system onto a serial ATA hard disk successfully, you need to install the SATA controller driver during OS installation. Without the driver, the hard disk may not be recognized during the Windows setup process. First of all, copy the driver for the SATA controller from the motherboard driver CD-ROM to a floppy disk. See the instructions below about how to copy the driver in MS-DOS mode(Note). Prepare a startup disk that has CD-ROM support and a blank formatted floppy disk. Step 1: Insert the prepared startup disk and motherboard driver CD-ROM in your system. Boot from the startup disk. Once at the A:\> prompt, change to the CD-ROM drive (example: D:\>). At the D:\> prompt, type the following two commands. Press ENTER after each command (Figure 10): cd bootdrv menu Step 2: When the controller menu (Figure 11) appears, remove the startup disk and insert the blank formatted disk. Select the controller driver by pressing the corresponding letter from the menu. For example, from the menu in Figure 11, press H to select (H) nVIDIA MCP55 Series Raid (XP) if you wish to install Windows XP (32-bit). Your system will then automatically zip and transfer this driver file to the floppy disk. Press 0 to exit when finished. Figure 10 Figure 11 (Note) For users without a startup disk: Use an alternative system and insert the GIGABYTE motherboard driver CD-ROM. From the CD-ROM drive folder, double click the MENU.exe file in the BootDrv folder (Figure 12). A command prompt window will open similar to that in Figure 11. Figure 12 - 73 - Appendix

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Appendix
- 73 -
English
(4)
Making a SATA Driver Disk
To install operating system onto a serial ATA hard disk successfully, you need to install the SATA
controller driver during OS installation. Without the driver, the hard disk may not be recognized during
the Windows setup process.
First of all, copy the driver for the SATA controller from the motherboard
driver CD-ROM to a floppy disk. See the instructions below about how to copy the driver in MS-DOS
mode
(Note)
. Prepare a startup disk that has CD-ROM support and a blank formatted floppy disk.
Step 1: Insert the prepared startup disk and motherboard driver CD-ROM in your system.
Boot from the
startup disk. Once at the A:\> prompt, change to the CD-ROM drive (example: D:\>).
At the D:\>
prompt, type the following two commands. Press ENTER after each command (Figure 10):
cd bootdrv
menu
(Note)
For users without a startup disk:
Use an alternative system and insert the GIGABYTE motherboard driver CD-ROM.
From the
CD-ROM drive folder, double click the
MENU.exe
file in the
BootDrv
folder (Figure 12).
A
command prompt window will open similar to that in Figure 11.
Figure 10
Figure 11
Step 2: When the controller menu (Figure 11) appears, remove the startup disk and insert the blank
formatted disk.
Select the controller driver by pressing the corresponding letter from the menu.
For example, from the menu in Figure 11, press H to select
(H) nVIDIA MCP55 Series Raid (XP)
if
you wish to install Windows XP (32-bit). Your system will then automatically zip and transfer this driver
file to the floppy disk.
Press 0 to exit when finished.
Figure 12