Gigabyte GA-Z77X-UP4 TH Manual - Page 26

mSATA Solid-State Drive Connector, Controlled by the Intel Z77 Chipset, CLR_CMOS Clear CMOS Jumper

Get Gigabyte GA-Z77X-UP4 TH PDF manuals and user guides View all Gigabyte GA-Z77X-UP4 TH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

F_AUDIO(H) F_PANEL(NH) F_PANEL (H61M-D2) DIP 1 23 1 7) mSATA (Solid-State Drive Connector, Controlled by the Intel Z77 Chipset) The mSATA connector conforms to SATA 3Gb/s standard and can connect to a single solid-state drive. When the mSATA connector is installed with a solid-state drive, the SATA2_5 connector will become unavailable. DB_PORT BIOS Switcher (X58A-OC) 1 M_SATA mSATA Voltage measurement module(X58A-OC) PWM Switch (X58A-OC) ACPI_CPT (GA-IVB) DIP 1 23 1 DIP 1 23 1 DIP 1 23 PCIe power connector (SATA)(X58A-OC) SMB_CPT (GA-IVB) nts(G1.Sniper 3) 8) CLR_CMOS (Clear CMOS Jumper) CLR_CMOS CI DIS_ME GP15_CPT (GA-IVB) Use this jumper to clear the CMOS values (e.g. date information and BIOS configurations) and reset the CMOS values to factory defaults. To clear the CMOS values, use a metal object like a screwXDdPri_vCePrUto touch BIOS Stwhietchtewr o(SWpi4n)s for a few seconds. XDP_PCH (GA-IVB) Open: Normal Short: Clear CMOS Values •• Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS values. •• After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or manually configure the BIOS settings (refer to Chapter 2, "BIOS Setup," for BIOS configurations). Hardware Installation - 26 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
- 26 -
Hardware Installation
7)
mSATA (Solid-State Drive Connector, Controlled by the Intel Z77 Chipset)
The mSATA connector conforms to SATA 3Gb/s standard and can connect to a single solid-state drive. When
the mSATA connector is installed with a solid-state drive, the SATA2_5 connector will become unavailable.
mSATA
8)
CLR_CMOS (Clear CMOS Jumper)
Use this jumper to clear the CMOS values (e.g. date information and BIOS configurations) and reset the
CMOS values to factory defaults. To clear the CMOS values, use a metal object like a screwdriver to touch
the two pins for a few seconds.
•
Always turn off your computer and unplug the power cord from the power outlet before clearing
the CMOS values.
•
After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or
manually configure the BIOS settings (refer to Chapter 2, "BIOS Setup," for BIOS configurations).
Open: Normal
Short: Clear CMOS Values