Graco 1752033 Owners Manual - Page 67

Belt with Sliding Latch Plate, locking clip, To Install Locking Clip

Page 67 highlights

• Combination Lap/Shoulder Belt with Sliding Latch Plate This belt has a latchplate that slides freely along the belt. This belt MUST be converted to prevent movement of the lap portion of the belt. You must use the locking clip provided with the infant restraint, unless your vehicle's seat belt can be converted in another way as described in your vehicle owner's manual. Locking clip To Install Locking Clip: 1. Tighten the buckled belt by pushing down hard on the infant restraint and pulling hard on the shoulder belt. 2. While pushing down on infant restraint, pinch the two straps together behind the buckle tongue. Unbuckle the belt without allowing it to slip. ½ inch – 3. Connect lap and shoulder belts with locking clip as shown – — and —. 4. Rebuckle belt. Check that lap belt does not move by pulling and pushing hard on infant restraint. If belt loosens or lengthens, repeat procedure. Locking clip goes here, /1 2 inch from the buckle 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136

• Combination Lap/Shoulder
Belt with Sliding Latch Plate
This belt has a latchplate that
slides freely along the belt.
This belt
MUST
be converted to prevent
movement of the lap portion of the belt. You
must use the
locking clip
provided with the
infant restraint, unless your vehicle's seat belt
can be converted in another way as described
in your vehicle owner's manual.
To Install Locking Clip:
1.
Tighten the buckled belt by pushing
down hard on the infant restraint and
pulling hard on the shoulder belt.
2.
While pushing down on infant restraint,
pinch the two straps together behind
the buckle tongue. Unbuckle the
belt without allowing it to slip.
3.
Connect lap and shoulder belts
with locking clip as shown
and
.
4.
Rebuckle belt. Check that lap
belt does not move by pulling
and pushing hard on infant
restraint. If belt loosens or
lengthens, repeat procedure.
Locking clip
½
inch
Locking clip goes here,
1
/
2
inch from the buckle
27