Haier HL40XSLW2 User Manual - Page 29

D If user's input is incorrect, LED will blink 6 times in 3 seconds (2 HZ). And then keep 2 HZ blink, user now can return to step 3 and re-program the device. Within 30 seconds, user should enter the 3-digit brand code corresponding to your device. If time out or any key other than Power and digits is pressed, LED will be off and manually programming process is exit. YYManually scan mode With manually scan programming, the Controller tests all the codes available in the codeset database and assign the correct one for the selected device. Although this method is more time consuming, it saves you the trouble of looking up the brand codes necessary for manual programming. To manually-scan program the Controller: A Manually turn OFF the device for manually scan mode. (TV, VCR, DVD, STB, cable box or audio equipment). B Choose the device you want to program. C While Press and holding ENTER key, press INPUT key, and device LED will be ON. Keep the status for about 3 seconds and the LED will blink, indicating that the Control is ready for programming, then release both keys. D Press and release the CH+/CH- key. it will emit the next or the previous POWER key code. The LED blinks with 10 HZ freq, indicating that the Remote is in manually scan mode. E Press CH+/CH- key repeatedly until the device switches ON (CH+ key conducts a upward search while the CH- key conducts a downward search in the code set database). When the device turns ON, press and release the ENTER key to program the Controller with the new code, saving the code to EEPROM and exit. F After saving the new code, press POWER key. If the device responds, no further programming is required. If the device does not respond, repeat step 3 through 5. And searching will start from current code set. To exit without programming, press any key or no key was pressed in 30 seconds, manually scan mode will be automatically exit. The code can not be saved to EEPROM. After searching the entire data base, this mode will be automatically exited and led will blink for 3 times in Universal Remote Control 1.5 seconds. The code can not be saved to EEPROM. YYAutomatic Scan Programming the Controller To automatic scan program the Controller: A Manually turn OFF the device you wish to power scan. (TV, VCR, DVD,STB, cable box or audio equipment). B Choose the device you wish to program. C While Press and holding ENTER key, press the INPUT key and device LED will be ON. Keep the status for about 3 seconds and the LED will blink, indicating that the Controller is ready for programming, then release both keys. D Press and release the Mute key to enter automatic scan mode. And the remote will automatically sending codes to the device per 2 seconds. E When the device turns ON, press ENTER key to program the Controller with the new code, saving it to EEPROM and exit. F Press POWER key, If the device responds, no further programming is required. If the device does not respond repeat steps 1 through 5. G After searching the entire data base, this mode will be automatically exited and led will blink for 3 times. The codeset is not saved to EEPROM. In automatic scan mode, press any key other than ENTER key will exit without programming. Display mode A Choose the device you wish to program. B To enter display mode, while press and holding ENTER key, press the INPUT key and device LED will be ON, keep the status for about 3 seconds and the LED will blink, indicating that the Controller is ready for programming, then release both keys. C Sequence press 9, 8, 0 to enter display mode. D Press digit 1 key to get the first digit of current codeset. For example, if the first digit of codeset is 1, so then led will blink once and remains OFF. Digit "0" in codeset will not be displayed. Blink Freq is 1 HZ. E Press digit 2 key to get the second digit of current codeset. For example, if the second digit of codeset is 3, so then led will blink three times and remains OFF. Blink Freq is 1 HZ. Haier LED HDTV EN-28