Harman Kardon AVR 120 Owners Manual - Page 14

Installation and Connections - application note

Page 14 highlights

Installation and Connections System Installation After unpacking the unit, and placing it on a solid surface capable of supporting its weight, you will need to make the connections to your audio and video equipment. Audio Equipment Connections We recommend that you use high-quality interconnect cables when making connections to source equipment and recorders to preserve the integrity of the signals. When making connections to audio source equipment or speakers it is always a good practice to unplug the unit from the AC wall outlet. This prevents any possibility of accidentally sending audio or transient signals to the speakers that may damage them. 1. Connect the analog output of a CD player to the CD Inputs •. NOTE: When the CD player has both fixed and variable audio outputs it is best to use the fixed output unless you find that the input to the receiver is so low that the sound is noisy, or so high that the signal is distorted. 2. Connect the analog Play/Out jacks of a cassette deck, MD, CD-R or other audio recorder to the Tape Input Jacks ¡. Connect the analog Record/In jacks on the recorder to the Tape Output Jacks ™ on the AVR 120. 3. Connect the output of any digital sources to the appropriate input connections on the AVR 120 rear panel. Note that the Optical and Coaxial Digital Inputs de#$ may be used with a Dolby Digital or DTS source or the output of a conventional CD or LD player's PCM (S/P-DIF) output. To take advantage of the AVR 120's built-in MP3-decoding capabilities, you may also connect the digital output of a computer or sound card to this input, provided that the signal from the computer is in the S/P-DIF format. Check your computer or sound card's instructions to verify the type of output signal or use a transcoder such as the Harman Kardon DAL 150. 4. Connect the Optical Digital Output ª or Coaxial Digital Output , on the rear panel of the AVR 120 to the matching digital input connections on a CD-R or MiniDisc recorder. 5. Assemble the AM Loop Antenna supplied with the unit as shown below. Connect it to the AM and GND Screw Terminals ¢ . 6. Connect the supplied FM antenna to the FM Antenna (75 ohm) Connection ¶. The FM antenna may also be an external roof antenna, an inside powered or wire lead antenna or a connection from a cable TV system. Note that if the antenna or connection uses 300-ohm twinlead cable, you must use the 300-ohm-to-75ohm adapter supplied with the unit to make the connection. 7. Connect the front, center and surround Speaker Outputs › fi to the respective speakers. To ensure that all the audio signals are carried to your speakers without loss of clarity or resolution, we suggest that you use high-quality speaker cable. Many brands of cable are available and the choice of cable may be influenced by the distance between your speakers and the receiver, the type of speakers you use, personal preferences and other factors. Your dealer or installer is a valuable resource to consult in selecting the proper cable. Regardless of the brand of cable selected, we recommend that you use a cable constructed of fine, multistrand copper with a gauge of 14 or smaller. Remember that in specifying cable, the lower the number, the thicker the cable. Cable with a gauge of 16 may be used for short runs of less than ten feet. We do not recommend that you use cables with an AWG equivalent of 18 or higher due to the power loss and degradation in performance that will occur. Cables that are run inside walls should have the appropriate markings to indicate listing with UL, CSA or other appropriate testing agency standards. Questions about running cables inside walls should be referred to your installer or a licensed electrical contractor who is familiar with the NEC and/or the applicable local building codes in your area. When connecting wires to the speakers, be certain to observe proper polarity. Remember to connect the "negative" or "black" wire to the same terminal on both the receiver and the speaker. The AVR 120 is one of the first audio products with the latest CEA-recommended color-coding for speaker terminals. Accordingly, the positive (+) terminal, which was previously red, is now a specific color to assist you in making the correct connections. If your speakers have color-coded connections, match the terminal on the AVR 120 to the like terminal on your speakers. For existing speakers with a red terminal for the positive connection, the connections on the AVR 120 are as follows: Left Front = White Right Front = Red Center = Green Left Surround = Blue Right Surround = Grey NOTE: While most speaker manufacturers adhere to an industry convention of using black terminals for negative and red ones for positive, some manufacturers may vary from this configuration. To ensure proper phase and optimal performance, consult the identification plate on your speaker or the speaker's manual to verify polarity. If you do not know the polarity of your speaker, ask your dealer for advice before proceeding, or consult the speaker's manufacturer. We also recommend that the length of cable used to connect speaker pairs be identical. For example, use the same length piece of cable to connect the front-left and front-right or surround-left and surround-right speakers, even if the speakers are a different distance from the AVR 120. 8. Connections to a subwoofer are normally made via a line-level audio connection from the Subwoofer Output ‹ to the line-level input of a subwoofer with a built-in amplifier. When a passive subwoofer is used, the connection first goes to a power amplifier, which will be connected to one or more subwoofer speakers. If you are using a powered subwoofer that does not have line-level input connections, follow the instructions furnished with the speaker for connection information. Video Equipment Connections Video equipment is connected in the same manner as audio components. Again, the use of highquality interconnect cables is recommended to preserve signal quality. 1. Connect a VCR's audio and video Play/Out jacks to the Video 1 Input Jacks £a on the rear panel. The Audio and Video Record/In jacks on the VCR should be connected to the Video 1 Out Jacks ∞· on the AVR 120. 14 INSTALLATION AND CONNECTIONS

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44

14
INSTALLATION AND CONNECTIONS
System Installation
After unpacking the unit, and placing it on a solid
surface capable of supporting its weight, you will
need to make the connections to your audio and
video equipment.
Audio Equipment Connections
We recommend that you use high-quality inter-
connect cables when making connections to
source equipment and recorders to preserve the
integrity of the signals.
When making connections to audio source
equipment or speakers it is always a good prac-
tice to unplug the unit from the AC wall outlet.
This prevents any possibility of accidentally
sending audio or transient signals to the speak-
ers that may damage them.
1. Connect the analog output of a CD player to
the
CD Inputs
.
NOTE:
When the CD player has both fixed and
variable audio outputs it is best to use the fixed
output unless you find that the input to the
receiver is so low that the sound is noisy, or so
high that the signal is distorted.
2. Connect the analog Play/Out jacks of a cas-
sette deck, MD, CD-R or other audio recorder to
the
Tape Input Jacks
¡
. Connect the analog
Record/In jacks on the recorder to the
Tape
Output Jacks
on the AVR 120.
3. Connect the output of any digital sources
to
the appropriate input connections on the
AVR 120 rear panel. Note that the
Optical
and
Coaxial Digital Inputs
de
#$
may
be used with a Dolby Digital or DTS source or
the output of a conventional CD or LD player
s
PCM (S/P-DIF) output. To take advantage of
the AVR 120
s built-in MP3-decoding capabili-
ties, you may also connect the digital output
of a computer or sound card to this input,
provided that the signal from the computer is
in the S/P-DIF format. Check your computer or
sound card
s instructions to verify the type of
output signal or use a transcoder such as the
Harman Kardon DAL 150.
4. Connect the
Optical Digital Output
ª
or
Coaxial Digital Output
on the rear panel of
the AVR 120 to the matching digital input connec-
tions on a CD-R or MiniDisc recorder.
5. Assemble the AM Loop Antenna supplied
with the unit as shown below. Connect it to the
AM
and
GND Screw Terminals
¢
.
6. Connect the supplied FM antenna to the
FM
Antenna (75 ohm) Connection
. The FM
antenna may also be an external roof antenna,
an inside powered or wire lead antenna or a
connection from a cable TV system. Note that if
the antenna or connection uses 300-ohm twin-
lead cable, you must use the 300-ohm-to-75-
ohm adapter supplied with the unit to make
the connection.
7. Connect the front, center and surround
Speaker Outputs
›fi
to the respective
speakers.
To ensure that all the audio signals are carried
to your speakers without loss of clarity or reso-
lution, we suggest that you use high-quality
speaker cable. Many brands of cable are avail-
able and the choice of cable may be influenced
by the distance between your speakers and the
receiver, the type of speakers you use, personal
preferences and other factors. Your dealer or
installer is a valuable resource to consult in
selecting the proper cable.
Regardless of the brand of cable selected, we
recommend that you use a cable constructed of
fine, multistrand copper with a gauge of 14 or
smaller. Remember that in specifying cable, the
lower the number, the thicker the cable.
Cable with a gauge of 16 may be used for short
runs of less than ten feet. We do not recom-
mend that you use cables with an AWG equiva-
lent of 18 or higher due to the power loss and
degradation in performance that will occur.
Cables that are run inside walls should have the
appropriate markings to indicate listing with UL,
CSA or other appropriate testing agency stan-
dards. Questions about running cables inside
walls should be referred to your installer or a
licensed electrical contractor who is familiar
with the NEC and/or the applicable local build-
ing codes in your area.
When connecting wires to the speakers, be cer-
tain to observe proper polarity. Remember to
connect the
negative
or
black
wire to the
same terminal on both the receiver and the
speaker.The AVR 120 is one of the first audio
products with the latest CEA-recommended
color-coding for speaker terminals.Accordingly,
the positive (+) terminal, which was previously
red, is now a specific color to assist you in mak-
ing the correct connections. If your speakers
have color-coded connections, match the termi-
nal on the AVR 120 to the like terminal on your
speakers. For existing speakers with a red termi-
nal for the positive connection, the connections
on the AVR 120 are as follows:
Left Front = White
Right Front = Red
Center = Green
Left Surround = Blue
Right Surround = Grey
NOTE:
While most speaker manufacturers
adhere to an industry convention of using black
terminals for negative and red ones for positive,
some manufacturers may vary from this config-
uration. To ensure proper phase and optimal
performance, consult the identification plate on
your speaker or the speaker
s manual to verify
polarity. If you do not know the polarity of your
speaker, ask your dealer for advice before pro-
ceeding, or consult the speaker
s manufacturer.
We also recommend that the length of cable
used to connect speaker pairs be identical.
For example, use the same length piece of
cable to connect the front-left and front-right
or surround-left and surround-right speakers,
even if the speakers are a different distance
from the AVR 120.
8. Connections to a subwoofer are normally
made via a line-level audio connection from the
Subwoofer Output
to the line-level input
of a subwoofer with a built-in amplifier. When a
passive subwoofer is used, the connection first
goes to a power amplifier, which will be con-
nected to one or more subwoofer speakers. If
you are using a powered subwoofer that does
not have line-level input connections, follow the
instructions furnished with the speaker for con-
nection information.
Video Equipment Connections
Video equipment is connected in the same man-
ner as audio components. Again, the use of high-
quality interconnect cables is recommended to
preserve signal quality.
1. Connect a VCR
s audio and video Play/Out
jacks to the
Video 1 Input Jacks
£a
on
the rear panel. The Audio and Video Record/In
jacks on the VCR should be connected to the
Video 1 Out Jacks
∞·
on the AVR 120.
Installation and Connections