Harman Kardon AVR 147 Owners Manual - Page 26

Step Nine - Turn On the AVR 147

Get Harman Kardon AVR 147 PDF manuals and user guides View all Harman Kardon AVR 147 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

INSTALLATION Step Nine - Turn On the AVR 147 Two steps are required the first time you turn on the AVR 147. 1. Gently press the Master Power Switch until the word OFF is no longer visible. The Power Indicator above the two power switches should light up in amber, indicating that the AVR is in Standby mode and is ready to be turned on. See Figure 35. Normally, you may leave the Master Power Switch in the ON position, even when the receiver is not being used. Figure 35 - Power Switches 2. There are several ways in which the AVR 147 may be turned on from Standby mode. a) Press the Standby/On Switch on the front panel. See Figure 35. b) Press the Source Select Button on the front panel. See Figure 36. Figure 36 - Source Select Button c) Using the remote, press any one of these buttons: AVR, DVD/CD, TAPE/The Bridge, HDMI 1/HDMI 2, VID1, VID2, VID3, XM, AM/FM or 6CH. See Figure 37. Figure 37 - AVR and Input Selectors NOTE: Any time you press one of the Input Selectors on the remote (i.e., DVD/CD, TAPE/The Bridge, HDMI 1/HDMI 2, VID1, VID2 or VID3), the remote will switch modes so that it will only transmit the codes programmed to operate that device. In order to control the receiver, you will need to press the AVR button to return the remote to AVR mode. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
26
INSTALLATION
Step Nine – Turn On the AVR 147
Two steps are required the first time you turn on the AVR 147.
1. Gently press the Master Power Switch until the word OFF is no longer
visible. The Power Indicator above the two power switches should
light up in amber, indicating that the AVR is in Standby mode and is
ready to be turned on. See Figure 35. Normally, you may leave the
Master Power Switch in the ON position, even when the receiver is
not being used.
Figure 35 –
Power Switches
2. There are several ways in which the AVR 147 may be turned on from
Standby mode.
a) Press the Standby/On Switch on the front panel. See Figure 35.
b) Press the Source Select Button on the front panel. See Figure 36.
Figure 36 –
Source Select Button
c) Using the remote, press any one of these buttons: AVR, DVD/CD,
TAPE/The Bridge, HDMI 1/HDMI 2, VID1, VID2, VID3, XM, AM/FM
or 6CH. See Figure 37.
Figure 37 –
AVR and Input Selectors
NOTE:
Any time you press one of the Input Selectors on
the remote (i.e., DVD/CD,TAPE/The Bridge, HDMI 1/HDMI 2,
VID1, VID2 or VID3), the remote will switch modes so that it will
only transmit the codes programmed to operate that device. In
order to control the receiver, you will need to press the AVR
button to return the remote to AVR mode.