Harman Kardon AVR 147 Owners Manual - Page 28

IMPORTANT SAFETY NOTE, Step One, Step Two, Step Three, Step Four - osd

Get Harman Kardon AVR 147 PDF manuals and user guides View all Harman Kardon AVR 147 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

INITIAL SETUP Before beginning, eliminate extraneous background noise that might affect the results, such as noisy air conditioning. Try to avoid making any loud noises while running EzSet/EQ. IMPORTANT SAFETY NOTE: During the EzSet/EQ procedure, a series of very loud test tones will be played through all of the speakers. Avoid sitting or standing close to any one speaker during the procedure. If you are particularly sensitive to loud noises, you may wish to leave the room and have someone else run EzSet/EQ. Step One - Place the included EzSet/EQ microphone in the listening position, or in the center of the room, at about the same height as the listeners' ears. The microphone features a threaded insert on the bottom so that it can be mounted on a camera tripod for stability. Step Two - Plug the EzSet/EQ microphone into the Headphone Jack/EzSet Microphone Input Jack on the front of the receiver. See Figure 40. Step Four - If you forgot to plug in the microphone, a message will flash at the bottom of the screen. If the microphone has been plugged in, a warning message will appear and remain on screen for several seconds (see Figure 42). Figure 42 - EzSet/EQ Warning Screen Please be patient until the warning screen is replaced by the main EzSet/EQ screen. See Figure 43. Figure 40 - Plug EzSet/EQ microphone into receiver. Step Three - Make sure that the AVR 147 and the video display are turned on. Press the OSD Button to display the Master Menu. See Figures 38 and 39. Use the ⁄/¤ Buttons to move the cursor to the EzSet/EQ line, and then press the Set Button to select the EzSet/EQ menu. See Figure 41. Figure 43 - EzSet/EQ Main Screen The cursor will be pointing to the word MEASUREMENT at the top of the screen. Use the ‹/› Buttons on the remote to select START. See Figures 44 and 45. Figure 41 - EzSet/EQ Menu Screen The cursor will be next to the word YES. Press the Set Button to begin EzSet/EQ. Figure 44 - EzSet/EQ - Specifying a 5.1 System 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
28
INITIAL SETUP
Before beginning, eliminate extraneous background noise that might
affect the results, such as noisy air conditioning. Try to avoid making
any loud noises while running EzSet/EQ.
IMPORTANT SAFETY NOTE:
During the EzSet/EQ procedure,
a series of very loud test tones will be played through all of the
speakers. Avoid sitting or standing close to any one speaker
during the procedure. If you are particularly sensitive to loud
noises, you may wish to leave the room and have someone
else run EzSet/EQ.
Step One –
Place the included EzSet/EQ microphone in the listening
position, or in the center of the room, at about the same height as the
listeners’ ears. The microphone features a threaded insert on the bottom
so that it can be mounted on a camera tripod for stability.
Step Two –
Plug the EzSet/EQ microphone into the Headphone
Jack/EzSet Microphone Input Jack on the front of the receiver. See
Figure 40.
Figure 40 – Plug EzSet/EQ microphone into receiver.
Step Three –
Make sure that the AVR 147 and the video display are
turned on. Press the OSD Button to display the Master Menu. See
Figures 38 and 39. Use the
⁄
/
¤
Buttons to move the cursor to the
EzSet/EQ line, and then press the Set Button to select the EzSet/EQ
menu. See Figure 41.
Figure 41 – EzSet/EQ Menu Screen
The cursor will be next to the word YES. Press the Set Button to
begin EzSet/EQ.
Step Four –
If you forgot to plug in the microphone, a message will
flash at the bottom of the screen. If the microphone has been plugged
in, a warning message will appear and remain on screen for several
seconds (see Figure 42).
Figure 42 – EzSet/EQ Warning Screen
Please be patient until the warning screen is replaced by the main
EzSet/EQ screen. See Figure 43.
Figure 43 – EzSet/EQ Main Screen
The cursor will be pointing to the word MEASUREMENT at the top
of the screen. Use the
‹
/
›
Buttons on the remote to select START.
See Figures 44 and 45.
Figure 44 – EzSet/EQ – Specifying a 5.1 System