Harman Kardon AVR 2700 Owners Manual - Page 27
Automatic Setup - EzSet/EQ, Speaker Setup - review
View all Harman Kardon AVR 2700 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 27 highlights
ENGLISH AVR Set Up the AVR 5. Press the remote control's AVR button. The AVR's on-screen display (OSD) Main Menu screen will appear on the TV. Source Select Select the Source Device Setup Source Setup Source Devices Speaker Setup Speaker Optimization, EQ Zone 2 Manage and Control Zone 2 System General AVR Settings Settings Lock Manage System Lock 6. Use the remote's Up/Down/Left/Right and OK buttons to select "Speaker Setup." Speaker Setup Automatic Setup - EzSet/EQ Automated Speaker Setup and EQ Manual Setup Manually Adjust Speaker Settings 7. Select "Automatic Setup - EzSet/EQ" and then select "Continue." 8. Select the number of speakers in your system. Select "5.1" if no surround back or front height speakers are present or if you will be using the Assigned Amp channels for multizone operation. 9. The test will begin. Make sure that the room is quiet while the test noise is playing through the speakers. 10. When the test finishes, select "Continue," then select "View Settings" to see the results of the EzSet/EQ process, or select "Done" to exit. NOTES: s If there are fewer than five main speakers in your system, do not use the EzSet/ EQ process. Instead, proceed as described in Manual Speaker Setup, on page 36. s If you are using a 6.1-channel configuration with a single surround back speaker, use EzSet/EQ automatic configuration for 5.1 speakers, connect the single surround back speaker to the left Assigned Amp Speaker Output connector, then configure the surround back speaker manually, as described in Manual Speaker Setup, on page 36. Set Up Your Sources The Setup Source menu lets you assign the correct physical audio and video connections to each source and lets you set many audio and video playback features for each source. IMPORTANT: The "Video Input from Source," "Audio Input from Source" and "Resolution to Display" settings are not optional and must be adjusted before you use your AVR to enable playback of each source. You can adjust the other settings later. See System Settings, on page 39, for complete information about adjusting all of the Settings menu options. 1. Review the assigned connectors you listed on the Source Buttons and Assigned Connectors table, on page 18. Note what changes (if any) you want to make from the default source-button connector assignments that appear on the list. (If there are no changes, you can skip this section.) 2. To display the Source Settings menu for the active source, press the Info button on the front panel or remote. Or, from the Main Menu screen, select "Setup Source" and select a source from the slide-in menu. The Settings menu for that source will appear. Cable/Sat Audio Effects Video Modes: Surround Modes: Audio Format from Source: Video Input from Source: Audio Input from Source: Resolution to Display: Resolution from Source: HDMI Bypass: Change Name: Adjust Lip Sync Off Auto Select NO AUDIO INPUT HDMI 2 HDMI 2 720p - 60Hz No Input Off Cable/Sat 3. Select "Video Input From Source" and select the video input connector you want to assign to the source button. Press the OK button. NOTE: If you select an HDMI connector as the Video Input from Source, the Audio Input from Source will automatically change to the same HDMI connector. If you want to use a different audio connection, proceed to step 4. Cable/Sat Audio Effects Video Modes: Surround Modes: Audio Format from Source: Video Input from Source: Audio Input from Source: Resolution to Display: Resolution from Source: HDMI Bypass: Change Name: Adjust Lip Sync Zone 2 Audio: Off Auto Select No Audio Input HDMI 2 HDMI 2 1080p - 60Hz No Video Input Auto Cable/Sat Analog 1 HDMI 1 HDMI 2 HDMI 3 HDMI 4 HDMI 5 HDMI 6 HDMI 7 HDMI Front Component Composite 1 27