HP 10/100 3Com 3C905B-TX 3COM LAN cards (D6500A, D6509A), User Guide - Page 44

Checking the Remote Wake-up Function, 3Com DOS Diagnostic Program

Get HP 10/100 3Com 3C905B-TX PDF manuals and user guides View all HP 10/100 3Com 3C905B-TX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

4 Troubleshooting Checking the Remote Wake-up Function Checking the Remote Wake-up Function NOTE Check that the WOL connector cable is connected to the network interface card and to the PC's system board. • If the PC has been powered off (for example, due to an electrical power failure, or because the power cord has been removed), the Remote Power On (RPO) will not work. To enable the RPO, you must first power on the PC, allow Windows 95 or NT 4.0 to boot, then shut down the PC. • Check that the WOL connector cable is connected to the network interface card and to the PC's system board. • Check that the LAN-specific fields in the HP PC Setup utility are correctly set (see Chapter 2). • Check that you are running the latest driver software. The latest driver and utilities are available from the HP Support Web site: http://www.hp.com/go/vectrasupport RPO is only supported under Windows 95 and Windows NT 4.0. 3Com DOS Diagnostic Program For information about running the 3Com DOS diagnostic program, see the INSTRUCT.TXT text file in the HELP directory on EtherDisk Diskette #1. Crossover Cable Troubleshooting Tips When you work with network cabling, concentrators, and NICs from different vendors, it is possible to connect everything and still have no communication between file servers and workstations. 44 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
4
Troubleshooting
Checking the Remote Wake-up Function
44
English
Checking the Remote Wake-up Function
Check that the WOL connector cable is connected to the network
interface card and to the PC’s system board.
•
If the PC has been powered off (for example, due to an electrical
power failure, or because the power cord has been removed), the
Remote Power On (RPO) will not work. To enable the RPO, you must
first power on the PC, allow Windows 95 or NT 4.0 to boot, then shut
down the PC.
•
Check that the WOL connector cable is connected to the network
interface card and to the PC’s system board.
•
Check that the LAN-specific fields in the HP PC
Setup
utility are
correctly set (see Chapter 2).
•
Check that you are running the latest driver software. The latest
driver and utilities are available from the HP Support Web site:
NOTE
RPO is only supported under Windows 95 and Windows NT 4.0.
3Com DOS Diagnostic Program
For information about running the 3Com DOS diagnostic program, see
the INSTRUCT.TXT text file in the HELP directory on
EtherDisk
Diskette #1
.
Crossover Cable Troubleshooting Tips
When you work with network cabling, concentrators, and NICs from
different vendors, it is possible to connect everything and still have no
communication between file servers and workstations.