HP 110-023w Regulatory, Safety and Environmental Notices User Guide - Page 37

Laser safety, Power supply and power cord set requirements

Get HP 110-023w PDF manuals and user guides View all HP 110-023w manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Laser safety For products equipped with optical drives or fiber optic transceivers. This product may be provided with an optical storage device (i.e., CD or DVD drive) and/or fiber optic transceiver. These contain lasers and are classified as Class 1 Laser Products in accordance with the standard IEC/EN 60825-1 and comply with its requirements. Each laser product complies with US FDA Regulations of 21 CFR 1040.10 and 1040.11 or complies with those regulations except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007. WARNING! Use of controls or adjustments or performance of procedures other than those specified herein or in the laser product's installation guide may result in hazardous radiation exposure. To reduce the risk of exposure to hazardous radiation: • Do not try to open the module enclosure. There are no user-serviceable components inside. • Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein. • Allow only HP Authorized Service technicians to repair the unit. Power supply and power cord set requirements Power supply class I grounding requirements For protection from fault currents, the equipment shall be connected to a grounding terminal. Plug the system power cord into an AC outlet that provides a ground connection. Substitute cords may not provide adequate fault protection. Only use the power cord supplied with this product or a HewlettPackard authorized replacement. Brazil notice Este equipamento deve ser conectado obrigatoriamente em tomada de rede de energia elétrica que possua aterramento (três pinos), conforme a norma nbr abnt 5410,visando a segurança dos usuários contra choques elétricos. Denmark For tilslutning af de øvrige ledere, se medfølgende installationsvejledning. Finland Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan. Norway Apparatet må kun tilkoples jordet stikkontakt. Sweden Apparaten skall anslutas till jordat uttag, när den ansluts till ett nätverk. Power supply requirements The power supplies on some products have external power switches. The voltage select switch feature on the product permits it to operate from any line voltage between 100-127 or 200-240 volts Laser safety 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
Laser safety
For products equipped with optical drives or fiber optic transceivers.
This product may be provided with an optical storage device (i.e., CD or DVD drive) and/or fiber optic
transceiver. These contain lasers and are classified as Class 1 Laser Products in accordance with the
standard IEC/EN 60825-1 and comply with its requirements.
Each laser product complies with US FDA Regulations of 21 CFR 1040.10 and 1040.11 or complies
with those regulations except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007.
WARNING!
Use of controls or adjustments or performance of procedures other than those specified
herein or in the laser product’s installation guide may result in hazardous radiation exposure. To
reduce the risk of exposure to hazardous radiation:
• Do not try to open the module enclosure. There are no user-serviceable components inside.
• Do not operate controls, make adjustments, or perform procedures to the laser device other than
those specified herein.
• Allow only HP Authorized Service technicians to repair the unit.
Power supply and power cord set requirements
Power supply class I grounding requirements
For protection from fault currents, the equipment shall be connected to a grounding terminal. Plug the
system power cord into an AC outlet that provides a ground connection. Substitute cords may not
provide adequate fault protection. Only use the power cord supplied with this product or a Hewlett-
Packard authorized replacement.
Brazil notice
Este equipamento deve ser conectado obrigatoriamente em tomada de rede de energia elétrica que
possua aterramento (três pinos), conforme a norma nbr abnt 5410,visando a segurança dos usuários
contra choques elétricos.
Denmark
For tilslutning af de øvrige ledere, se medfølgende installationsvejledning.
Finland
Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.
Norway
Apparatet må kun tilkoples jordet stikkontakt.
Sweden
Apparaten skall anslutas till jordat uttag, när den ansluts till ett nätverk.
Power supply requirements
The power supplies on some products have external power switches. The voltage select switch
feature on the product permits it to operate from any line voltage between 100-127 or 200-240 volts
Laser safety
29