HP 110-023w Regulatory, Safety and Environmental Notices User Guide - Page 38

For use in Norway, Power cord set requirements, Japan power cord requirements, Pinch hazard

Get HP 110-023w PDF manuals and user guides View all HP 110-023w manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

AC. Power supplies on those products that do not have external power switches are equipped with internal circuits that sense the incoming voltage and automatically switch to the proper voltage. For safety reasons, use only the AC adapter provided with the unit or an authorized replacement adapter from Hewlett-Packard. Replacement part numbers may be found at http://www.hp.com/cgibin/hpsupport/index.pl. For use in Norway This product is also designed for an IT power system with phase-to-phase voltage 230V. Power cord set requirements The power cord set received with the product meets the requirements for use in the country where the equipment was originally purchased. Use only the power cord provided with the unit or an authorized replacement power cord from Hewlett-Packard or an approved HP source. Replacement part numbers may be found at http://www.hp.com/cgi-bin/hpsupport/index.pl. Power cord sets for use in other countries must meet the requirements of the country where you use the product. For more information on power cord set requirements, contact your authorized HP dealer, reseller, or service provider. WARNING! Do not use power cords from other products. Mismatched power cords may result in a shock and fire hazard. The requirements listed below are applicable to all countries: 1. The power cord must be approved by an acceptable accredited agency responsible for evaluation in the country where the power cord set will be installed. 2. The length of the power cord must be between 1.8 m (6 feet) and 3.6 m (12 feet). For a power cord 2.0 m (6.56 feet) or less, the diameter of the wire must be a minimum of 0.75 mm2 or 18AWG. If the power cord is longer than 2.0 m (6.56 feet), the diameter of the wire must be a minimum of 1.0 mm2 or 16AWG. The power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it. Particular attention should be paid to the plug, electrical outlet, and the point where the cord exits from the product. WARNING! Do not operate this product with a damaged power cord set. If the power cord set is damaged in any manner, replace it immediately. Damaged cords may result in user exposure to hazards. Japan power cord requirements For use in Japan, use only the power cord received with this product. CAUTION: Do not use the power cord received with this product on any other products. Pinch hazard WARNING! Observe pinch hazard areas. Keep fingers away from closing parts. 30 Chapter 4 Safety notices for desktops, thin clients and personal workstations

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
AC. Power supplies on those products that do not have external power switches are equipped with
internal circuits that sense the incoming voltage and automatically switch to the proper voltage.
For safety reasons, use only the AC adapter provided with the unit or an authorized replacement
adapter from Hewlett-Packard. Replacement part numbers may be found at
cgi-
bin/hpsupport/index.pl
.
For use in Norway
This product is also designed for an IT power system with phase-to-phase voltage 230V.
Power cord set requirements
The power cord set received with the product meets the requirements for use in the country where
the equipment was originally purchased. Use only the power cord provided with the unit or an
authorized replacement power cord from Hewlett-Packard or an approved HP source. Replacement
part numbers may be found at
cgi-bin/hpsupport/index.pl
.
Power cord sets for use in other countries must meet the requirements of the country where you use
the product. For more information on power cord set requirements, contact your authorized HP
dealer, reseller, or service provider.
WARNING!
Do not use power cords from other products.
Mismatched power cords may result in a shock and fire hazard.
The requirements listed below are applicable to all countries:
1.
The power cord must be approved by an acceptable accredited agency responsible for
evaluation in the country where the power cord set will be installed.
2.
The length of the power cord must be between 1.8 m (6 feet) and 3.6 m (12 feet). For a power
cord 2.0 m (6.56 feet) or less, the diameter of the wire must be a minimum of 0.75 mm
2
or
18AWG. If the power cord is longer than 2.0 m (6.56 feet), the diameter of the wire must be a
minimum of 1.0 mm
2
or 16AWG.
The power cord should be routed so that it is not likely to be walked on or pinched by items placed
upon it or against it. Particular attention should be paid to the plug, electrical outlet, and the point
where the cord exits from the product.
WARNING!
Do not operate this product with a damaged power cord set. If the power cord set is
damaged in any manner, replace it immediately. Damaged cords may result in user exposure to
hazards.
Japan power cord requirements
For use in Japan, use only the power cord received with this product.
CAUTION:
Do not use the power cord received with this product on any other products.
Pinch hazard
WARNING!
Observe pinch hazard areas. Keep fingers away from closing parts.
30
Chapter 4
Safety notices for desktops, thin clients and personal workstations