Home » HP Manuals » Storage Adapters » HP 273914-B21 » Manual Viewer

HP 273914-B21 Smart Array 6400 Series Controllers for Integrity Servers User G - Page 19

Upgrading or replacing controller options, Replacing a battery

UPC - 613326361313

Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Upgrading or replacing controller options In this section Replacing a battery ...19 Replacing the expansion module...20 Replacing a battery WARNING: There is a risk of explosion, fire, or personal injury if the battery pack is not properly handled. Refer to "Battery replacement notice (on page 38)" before installing or removing any item that contains a battery pack. IMPORTANT: Whether you are replacing the main cache battery or the secondary (lower) cache battery, remove both batteries so that the board circuitry recognizes the new battery pack. 1. Close all applications, and then power down the server. This procedure flushes all data from the cache. 2. Remove the cache module: a. Open the ejector latches on each side of the DIMM connector (1). b. Pull the cache module out of the DIMM slot (2). 3. If the main cache battery must be replaced: a. Press the battery retainer tabs down, and push them through to the other side of the cache board (1). Upgrading or replacing controller options 19

Section	Page
HP Smart Array 6400 Series Controllers for Integrity Servers User Guide	1
Notice	2
Contents	3
Hardware features	5
Board components	5
Expansion module components	6
Controller specifications and attributes	6
Overview of the installation procedure	8
Quick installation procedure (Windows or Linux)	8
Installing the controller hardware	10
Before beginning the installation	10
Preparing the server	10
Installing the controller board	10
Connecting storage devices	11
Connecting internal storage	11
Connecting external storage	12
SCSI cable part numbers	12
Updating the firmware	13
Methods for updating the firmware (Windows® or Linux®)	13
Configuring an array	14
Introduction	14
Comparing the utilities	14
Using ORCA	15
Using ACU	16
Installing device drivers and Management Agents	17
Systems using Microsoft Windows	17
Installing device drivers	17
Installing Management Agents	17
Systems using Linux®	17
Installing Management Agents	18
Upgrading or replacing controller options	19
Replacing a battery	19
Replacing the expansion module	20
Replacing, moving, or adding hard drives	22
Identifying the status of a hard drive	22
Hot-plug SCSI hard drive LED combinations	22
Recognizing hard drive failure	23
Effects of a hard drive failure	23
Compromised fault tolerance	24
Recovering from compromised fault tolerance	24
Replacing hard drives	24
Factors to consider before replacing hard drives	25
Automatic data recovery (rebuild)	25
Time required for a rebuild	26
Failure of another drive during rebuild	26
Upgrading hard drive capacity	26
Moving drives and arrays	27
Adding drives	28
Diagnosing array problems	30
Controller board runtime LEDs	30
Cache module LEDs	31
Diagnostic tools	32
Electrostatic discharge	33
Preventing electrostatic discharge	33
Grounding methods to prevent electrostatic discharge	33
Regulatory compliance notices	34
Federal Communications Commission notice	34
FCC rating label	34
Class A equipment	34
Class B equipment	34
Declaration of conformity for products marked with the FCC logo, United States only	35
Modifications	35
Cables	35
Canadian notice (Avis Canadien)	35
European Union regulatory notice	36
Disposal of waste equipment by users in private households in private households in the European Union	36
BSMI notice	37
Japanese notice	37
Korean notice A&B	37
Battery replacement notice	38
Taiwan battery recycling notice	38
Acronyms and abbreviations	39

Match case Limit results 1 per page

Upgrading or replacing controller options

In this section

Replacing a battery

................................................................................................................................

Replacing the expansion module

..............................................................................................................

Replacing a battery

WARNING:

There is a risk of explosion, fire, or personal injury if the battery pack is not

properly handled. Refer to "Battery replacement notice (on page

)" before installing or

removing any item that contains a battery pack.

IMPORTANT:

Whether you are replacing the main cache battery or the secondary (lower) cache battery,

remove both batteries so that the board circuitry recognizes the new battery pack.

Close all applications, and then power down the server. This procedure flushes all data from the

cache.

Remove the cache module:

Open the ejector latches on each side of the DIMM connector (1).

Pull the cache module out of the DIMM slot (2).

If the main cache battery must be replaced:

Press the battery retainer tabs down, and push them through to the other side of the cache board

(1).