HP 381513-B21 HP Smart Array Controllers for HP Integrity Servers User Guide - Page 10

Overview of the installation procedure, Quick installation procedure (Windows or Linux) - controller firmware

Get HP 381513-B21 - Smart Array P800 Controller RAID PDF manuals and user guides
UPC - 882780622029
View all HP 381513-B21 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Overview of the installation procedure Quick installation procedure (Windows or Linux) Before installing the controller, refer to the support matrix on the HP website (http://www.hp.com/products1/serverconnectivity) to confirm that the server and operating system support the controller. To install the controller: 1. Power down the server. 2. Unplug the AC power cord from the power outlet. 3. Unplug the power cord from the server. 4. Install the controller hardware ("Installing the controller hardware" on page 12). 5. If necessary, install additional physical drives. The number of drives in the server determines the RAID level that is autoconfigured when the server is powered up (next step). 6. Power up the server. 7. Update the controller firmware ("Methods for updating the firmware (Windows or Linux)" on page 15). When the firmware update process is complete, the server reboots and runs through a POST procedure. This POST procedure halts briefly during controller initialization and prompts you to open ORCA. 8. Open ORCA ("Configuring an array" on page 16). o If using a headless console, press the Esc+8 key combination. o Otherwise, press the F8 key. 9. Configure the logical boot drive, and then exit from ORCA. If the server is using Linux, controller installation is complete. When the server is next rebooted, the operating system detects the controller hardware and automatically installs the required driver. If the server is using Microsoft® Windows®, continue as follows: 1. Load the controller driver from EBSU on the Smart Setup media. (To load the driver, select Load OEM Boot Drivers in EBSU. For more information about Smart Setup, refer to the HP Smart Setup Guide on the Smart Setup media.) 2. Run Express Setup. 3. When you have finished installing the operating system as directed during the Express Setup procedure, remove the operating system CD, and then insert the Smart Setup media. 4. Install the Integrity Support Pack ("Installing device drivers and Management Agents" on page 19). Controller installation is complete. Overview of the installation procedure 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
Overview of the installation procedure
10
Overview of the installation procedure
Quick installation procedure (Windows or Linux)
Before installing the controller, refer to the support matrix on the HP website
(
) to confirm that the server and operating system
support the controller.
To install the controller:
1.
Power down the server.
2.
Unplug the AC power cord from the power outlet.
3.
Unplug the power cord from the server.
4.
Install the controller hardware ("
Installing the controller hardware
" on page
12
).
5.
If necessary, install additional physical drives.
The number of drives in the server determines the RAID level that is autoconfigured when the server is
powered up (next step).
6.
Power up the server.
7.
Update the controller firmware ("
Methods for updating the firmware (Windows or Linux)
" on page
15
).
When the firmware update process is complete, the server reboots and runs through a POST
procedure. This POST procedure halts briefly during controller initialization and prompts you to open
ORCA.
8.
Open ORCA ("
Configuring an array
" on page
16
).
o
If using a headless console, press the
Esc+8
key combination.
o
Otherwise, press the
F8
key.
9.
Configure the logical boot drive, and then exit from ORCA.
If the server is using Linux, controller installation is complete. When the server is next rebooted, the
operating system detects the controller hardware and automatically installs the required driver.
If the server is using Microsoft® Windows®, continue as follows:
1.
Load the controller driver from EBSU on the Smart Setup media. (To load the driver, select
Load OEM
Boot Drivers
in EBSU. For more information about Smart Setup, refer to the
HP Smart Setup Guide
on
the Smart Setup media.)
2.
Run Express Setup.
3.
When you have finished installing the operating system as directed during the Express Setup
procedure, remove the operating system CD, and then insert the Smart Setup media.
4.
Install the Integrity Support Pack ("
Installing device drivers and Management Agents
" on page
19
).
Controller installation is complete.