HP 3PAR StoreServ 7200 2-node HP 3PAR-to-3PAR Storage Peer Motion Guide (OS 3. - Page 22

Select Peer Volumes, Import Volumes, For Online or Minimally Disruptive Migration, select

Get HP 3PAR StoreServ 7200 2-node PDF manuals and user guides View all HP 3PAR StoreServ 7200 2-node manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

based on your system setup and the data migration selections you made for the Peer Motion configuration. • Online - Used to migrate virtual volumes that are exported to a host. Requires unzoning the host system from the source system. • Minimally disruptive - Used to migrate virtual volumes that are exported to a host. Requires shutting down the host system for a short period of time. Additionally, the destination system must be running OS version 3.1.2 or later. • Offline - Used to migrate virtual volumes that are not exported to a host. Exported volumes you want to migrate must first be unexported to use offline migration. No unzoning or system shutdown is required. The default migration type is online. NOTE: A warning message appears if either of the following licenses is missing: • Thin provisioning (needed to create a thin volume) • Domain (needed to add the volumes to a domain that is not the domain) When the migration host exists, a warning message appears to clean it up. To import a volume: 1. Select Peer Motion in the Manger Pane. 2. In the Common Actions panel, click Import Volume. The Import Volume wizard appears. See also: "Create Peer Volumes" (page 18) Select Peer Volumes 1. The type of migration is preselected based on the system set up and the settings you configured in the Create PM Configuration wizard. 2. For Online or Minimally Disruptive Migration, select the Host or Host Set|Linked Hosts that you want to import peer virtual volumes. If you select one volume that is a member of a domain, you must migrate all volumes in that domain. For Offline Migration, select the Virtual Volumes to migrate to the destination system. If one volume is a member of a domain, all selected volumes must belong to the same domain. NOTE: Only one group of source volumes can be imported to peer volumes on the destination system at the same time. NOTE: You must finish the import process completely before you can migrate additional volumes or remove admitted (peer) volumes. 3. Click Verify peer volumes to verify the peer volumes to be used. 4. Click Next to go to the Import Volumes page. Import Volumes 1. Select the virtual volumes to be configured during import to 2. Select allocation settings. You can assign Same As Source, Thin, or Full provisioning to the virtual volumes being imported. The default is Thin. 3. Select a User CPG and Copy CPG. 4. (Optional.) Select the Create virtual copies after importing volumes check box. a. Select Suffix or Full Name. b. Enter a suffix or name in the text box. 22 Using the Peer Motion Manager

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
based on your system setup and the data migration selections you made for the Peer Motion
configuration.
•
Online
– Used to migrate virtual volumes that are exported to a host. Requires unzoning the
host system from the source system.
•
Minimally disruptive
– Used to migrate virtual volumes that are exported to a host. Requires
shutting down the host system for a short period of time. Additionally, the destination system
must be running OS version 3.1.2 or later.
•
Offline
– Used to migrate virtual volumes that are not exported to a host. Exported volumes
you want to migrate must first be unexported to use offline migration. No unzoning or system
shutdown is required.
The default migration type is online.
NOTE:
A warning message appears if either of the following licenses is missing:
•
Thin provisioning (needed to create a thin volume)
•
Domain (needed to add the volumes to a domain that is not the
<none>
domain)
When the migration host exists, a warning message appears to clean it up.
To import a volume:
1.
Select
Peer Motion
in the Manger Pane.
2.
In the Common Actions panel, click
Import Volume
.
The
Import Volume
wizard appears.
See also:
“Create Peer Volumes” (page 18)
Select Peer Volumes
1.
The type of migration is preselected based on the system set up and the settings you configured
in the
Create PM Configuration
wizard.
2.
For Online or Minimally Disruptive Migration, select the
Host
or
Host Set|Linked Hosts
that
you want to import peer virtual volumes. If you select one volume that is a member of a domain,
you must migrate all volumes in that domain.
For Offline Migration, select the
Virtual Volumes
to migrate to the destination system. If one
volume is a member of a domain, all selected volumes must belong to the same domain.
NOTE:
Only one group of source volumes can be imported to peer volumes on the destination
system at the same time.
NOTE:
You must finish the import process completely before you can migrate additional
volumes or remove admitted (peer) volumes.
3.
Click
Verify peer volumes
to verify the peer volumes to be used.
4.
Click
Next
to go to the Import Volumes page.
Import Volumes
1.
Select the virtual volumes to be configured during import to
<destination system>
2.
Select allocation settings. You can assign
Same As Source
,
Thin
, or
Full
provisioning to the
virtual volumes being imported. The default is
Thin
.
3.
Select a
User CPG
and
Copy CPG
.
4.
(Optional.) Select the
Create virtual copies after importing volumes
check box.
a.
Select
Suffix
or
Full Name
.
b.
Enter a suffix or name in the text box.
22
Using the Peer Motion Manager