HP 3PAR StoreServ 7400 2-node HP 3PAR SmartStart 1.1.1 User's Guide ( - Page 14

Setting Up the HP 3PAR StoreServ Storage System, Locating the Serial Number

Get HP 3PAR StoreServ 7400 2-node PDF manuals and user guides View all HP 3PAR StoreServ 7400 2-node manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

3 Setting Up the HP 3PAR StoreServ Storage System You must initialize the HP 3PAR StoreServ Storage system before you can configure the storage system. The Storage System Setup wizard verifies your HP 3PAR storage system configuration, initializes the storage system, and runs initialization tests on the storage system. To set up and configure the HP 3PAR storage system: 1. Verify the Service Processor is on the same subnet of the network as the HP 3PAR StoreServ 7000 Storage system you are setting up. 2. Click the Set up the Storage System link in SmartStart wizard Step 2, Set up systems. 3. Enter the permanent Service Processor IP address. For more information on Service Processor IP addresses, see the HP 3PAR StoreServ 7000 Storage Installation Guide. 4. Enter the username setupusr. 5. Enter the password for setupusr you created in the Service Processor Setup wizard. Troubleshooting Access If you are unable to access the Storage System Setup wizard, collect the relevant log files and contact HP support. For more information, see "Troubleshooting System Setup" (page 17). Locating the Serial Number The 7-digit storage system serial number is located on the back of your HP 3PAR StoreServ Storage system next to the power switch for the node enclosure PCM, and begins with 16 (e.g., 1612345). 14 Setting Up the HP 3PAR StoreServ Storage System

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
3 Setting Up the HP 3PAR StoreServ Storage System
You must initialize the HP 3PAR StoreServ Storage system before you can configure the storage
system. The Storage System Setup wizard verifies your HP 3PAR storage system configuration,
initializes the storage system, and runs initialization tests on the storage system.
To set up and configure the HP 3PAR storage system:
1.
Verify the Service Processor is on the same subnet of the network as the HP 3PAR StoreServ
7000 Storage system you are setting up.
2.
Click the
Set up the Storage System
link in
SmartStart wizard
Step 2,
Set up systems
.
3.
Enter the permanent Service Processor IP address. For more information on Service Processor
IP addresses, see the
HP 3PAR StoreServ 7000 Storage Installation Guide
.
4.
Enter the username
setupusr
.
5.
Enter the password for
setupusr
you created in the Service Processor Setup wizard.
Troubleshooting Access
If you are unable to access the Storage System Setup wizard, collect the relevant log files and
contact HP support. For more information, see
“Troubleshooting System Setup” (page 17)
.
Locating the Serial Number
The 7-digit storage system serial number is located on the back of your HP 3PAR StoreServ Storage
system next to the power switch for the node enclosure
PCM
, and begins with
16
(e.g.,
1612345
).
14
Setting Up the HP 3PAR StoreServ Storage System