HP 3PAR StoreServ 7400 2-node HP 3PAR SmartStart 1.1.1 User's Guide ( - Page 16

Continuing SmartStart Setup, Troubleshooting: Adding the Storage System to the Service Processor

Get HP 3PAR StoreServ 7400 2-node PDF manuals and user guides View all HP 3PAR StoreServ 7400 2-node manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Continuing SmartStart Setup After the Storage System Setup wizard initializes the HP 3PAR StoreServ Storage system: 1. Click Finish in the Setup Progress and Results step to exit the Storage System Setup wizard. NOTE: The wizard continues to run tests in the background after you have exited the Storage System Setup wizard. If these tests discover any issues, the HP 3PAR Management Console will display details in the Alert tab relevant to the issue. • To install the Management Console, go to SmartStart wizard Step 6, Install the Management Console. • For more information on Alerts, start the Management Console and open the HP 3PAR Management Console Online Help. 2. Set up Local Notification. For more information, see "Setting Up Local Notification" (page 16). 3. Validate Remote Support setup. For more information, see "Validating Remote Support" (page 16). 4. Continue to SmartStart wizard Step 3, Connect to the storage system. Troubleshooting: Adding the Storage System to the Service Processor If the wizard is not able to successfully add your HP 3PAR StoreServ 7000 Storage system to the Service Processor, use the SPmaint module in SPOCC to add the storage system (using the "Add New InServ" option) to your Service Processor. For more information, see the HP 3PAR Service Processor Onsite Customer Care (SPOCC) User's Guide. To access this document, go to the HP 3PAR StoreServ Storage site and click the Support link for your product: http://www.hp.com/go/3par Setting Up Local Notification To set up Local Notification: Local Notification configures your HP 3PAR StoreServ Storage system to email you alerts as issues occur (for example, a CPG becomes low on space, a disk drive fails, and so on). 1. Enter your Service Processor network address. 2. Click Setup. 3. Click Enable Local Notification. (Note that a mailhost must also be configured in order to completely enable Local Notification.) For more information about Local Notification setup, see the HP 3PAR Service Processor Onsite Customer Care (SPOCC) Online Help. For more information about alerts, see the HP 3PAR Management Console Online Help. Validating Remote Support Remote Support validation is done as a part of the Service Processor setup. If you need to re-run the Remote Support validation, you can use the SPmaint module in HP 3PAR Service Processor Onsite Customer Care (SPOCC). 1. Log into SPOCC (https://) using the 3parcust username. 2. Click SPmaint→Network Configuration→Test 3PAR Secure Service Collector Server. 3. Verify that SPOCC displays Connectivity test to HP 3PAR Secure Service Collector Server successful. 4. Verify that the Service Processor is transferring files successfully: 16 Setting Up the HP 3PAR StoreServ Storage System

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
Continuing SmartStart Setup
After the Storage System Setup wizard initializes the HP 3PAR StoreServ Storage system:
1.
Click
Finish
in the
Setup Progress and Results
step to exit the Storage System Setup wizard.
NOTE:
The wizard continues to run tests in the background after you have exited the Storage
System Setup wizard. If these tests discover any issues, the HP 3PAR Management Console
will display details in the Alert tab relevant to the issue.
•
To install the Management Console, go to
SmartStart wizard
Step 6,
Install the
Management Console
.
•
For more information on Alerts, start the Management Console and open the
HP 3PAR
Management Console Online Help
.
2.
Set up Local Notification. For more information, see
“Setting Up Local Notification” (page
16)
.
3.
Validate Remote Support setup. For more information, see
“Validating Remote Support” (page
16)
.
4.
Continue to
SmartStart wizard
Step 3,
Connect to the storage system
.
Troubleshooting: Adding the Storage System to the Service Processor
If the wizard is not able to successfully add your HP 3PAR StoreServ 7000 Storage system to the
Service Processor, use the
SPmaint
module in SPOCC to add the storage system (using the “Add
New InServ” option) to your Service Processor.
For more information, see the
HP 3PAR Service Processor Onsite Customer Care (SPOCC) User’s
Guide
. To access this document, go to the HP 3PAR StoreServ Storage site and click the
Support
link for your product:
h
t
tp://w
w
w
.hp
.co
m/go/3par
Setting Up Local Notification
To set up Local Notification: Local Notification configures your HP 3PAR StoreServ Storage system
to email you alerts as issues occur (for example, a CPG becomes low on space, a disk drive fails,
and so on).
1.
Enter your Service Processor network address.
2.
Click
Setup
.
3.
Click
Enable Local Notification
. (Note that a mailhost must also be configured in order to
completely enable Local Notification.)
For more information about Local Notification setup, see the
HP 3PAR Service Processor Onsite
Customer Care (SPOCC) Online Help
. For more information about alerts, see the
HP 3PAR
Management Console Online Help
.
Validating Remote Support
Remote Support validation is done as a part of the Service Processor setup. If you need to re-run
the Remote Support validation, you can use the SPmaint module in HP 3PAR Service Processor
Onsite Customer Care (SPOCC).
1.
Log into SPOCC (
https://<SP IP>
) using the
3parcust
username.
2.
Click
SPmaint
→
Network Configuration
→
Test 3PAR Secure Service Collector Server
.
3.
Verify that SPOCC displays
Connectivity test to HP 3PAR Secure Service Collector Server
successful
.
4.
Verify that the Service Processor is transferring files successfully:
16
Setting Up the HP 3PAR StoreServ Storage System