HP 3PAR StoreServ 7400 2-node HP 3PAR StoreServ 7000 Storage Installation Guid - Page 29

Cable Management Arm, WARNING, CAUTION, HP 3PAR StoreServ, 7450 Cabling Configuration Guide

Get HP 3PAR StoreServ 7400 2-node PDF manuals and user guides View all HP 3PAR StoreServ 7400 2-node manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Figure 27 Cable Management Arm WARNING! To avoid risk of injury or damage to the equipment, do not stack anything on top of rail-mounted equipment or use it as a work surface when it is extended from the rack. CAUTION: Always plan the rack layout before installing the equipment. See HP 3PAR StoreServ 7000/7450 Cabling Configuration Guide for the best practices for node and drive enclosure positioning in specific configurations. To install the rail kit and service processor: 1. Adjust the length of the mounting rails. 2. Install the threaded-hole cage nuts and rail mounting pins into the rack hole positions where you want to install the component. Use two cage nuts and two rail mounting pins on the front of each rail, and two cage nuts and two rail mounting pins on the rear of each rail. Installing the Service Processor in the Storage System 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
Figure 27 Cable Management Arm
WARNING!
To avoid risk of injury or damage to the equipment, do not stack anything on top
of rail-mounted equipment or use it as a work surface when it is extended from the rack.
CAUTION:
Always plan the rack layout before installing the equipment. See
HP 3PAR StoreServ
7000/7450 Cabling Configuration Guide
for the best practices for node and drive enclosure
positioning in specific configurations.
To install the rail kit and service processor:
1.
Adjust the length of the mounting rails.
2.
Install the threaded-hole cage nuts and rail mounting pins into the rack hole positions where
you want to install the component. Use two cage nuts and two rail mounting pins on the front
of each rail, and two cage nuts and two rail mounting pins on the rear of each rail.
Installing the Service Processor in the Storage System
29