HP 4100n HP LaserJet 4100mfp -User Guide - Page 107

Troubleshooting an HPJetdirect print server, I/O CARD READY, LOSS OF CARRIER ERROR - i o card not ready

Get HP 4100n - LaserJet B/W Laser Printer PDF manuals and user guides View all HP 4100n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 107 highlights

Troubleshooting an HP Jetdirect print server If the HP Jetdirect 10/100TX print server cannot communicate with the network, use these steps to verify the operation of the print server. q Check the HP Jetdirect configuration page (to print, see "Using the embedded Web server" on page 138). • If the message I/O CARD READY does not appear on the HP Jetdirect configuration page, see the troubleshooting section of the HP Jetdirect Print Server Administrator's Guide. • The message LOSS OF CARRIER ERROR indicates that the print server failed to link to the network. q Check the link-speed indicators (10 or 100) on the print server. If both are off, the print server failed to link to the network. If the print server failed to link, verify that all cables are correctly connected. If all cables are correctly connected and the print server still fails to link, follow the steps below to reconfigure the print server: 1 Through the embedded Web server, use the EIO menu to set the link speed manually (10 or 100 Mbps) and duplex mode (full- or half-duplex) so that they match the network. For example, if the port on the network switch is set for 100TX fullduplex operation, you must set the print server for 100TX full-duplex operation. 2 Turn the product off and then back on. Check the print server operation. If the print server still fails to link, try a different network cable. Troubleshooting an HP Jetdirect print server 105

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
Troubleshooting an HP Jetdirect print server
105
Troubleshooting an HP Jetdirect print server
If the HP Jetdirect 10/100TX print server cannot communicate with the network, use
these steps to verify the operation of the print server.
●
Check the HP Jetdirect configuration page (to print, see
“Using the embedded Web
server” on page 138
).
•
If the message
I/O CARD READY
does not appear on the HP Jetdirect
configuration page, see the troubleshooting section of the
HP Jetdirect Print
Server Administrator’s Guide
.
•
The message
LOSS OF CARRIER ERROR
indicates that the print server failed to link
to the network.
●
Check the link-speed indicators (10 or 100) on the print server. If both are off, the
print server failed to link to the network.
If the print server failed to link, verify that all cables are correctly connected. If all cables
are correctly connected and the print server still fails to link, follow the steps below to
reconfigure the print server:
1
Through the embedded Web server, use the EIO menu to set the link speed
manually (10 or 100 Mbps) and duplex mode (full- or half-duplex) so that they match
the network. For example, if the port on the network switch is set for 100TX full-
duplex operation, you must set the print server for 100TX full-duplex operation.
2
Turn the product off and then back on. Check the print server operation. If the print
server still fails to link, try a different network cable.