HP 8/8 Access Gateway Administrator's Guide (53-1001760-01, June 2010) - Page 29

Port state description, command to disable the switch.

Get HP 8/8 PDF manuals and user guides View all HP 8/8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Enabling and disabling Access Gateway mode 2 When you disable AG mode, The switch automatically reboots and comes back online using the fabric switch configuration; the AG parameters, such as port mapping, and Failover and Failback are automatically removed. When the switch reboots, it starts in Fabric OS Native mode. To re-join the switch to the core fabric, refer to "Rejoining Fabric OS switches to a fabric" on page 67. 9. Enter the switchDisable command to disable the switch. switch:admin> switchdisable 10. Enter the ag command with the --modedisable operand to disable AG mode. switch:admin> ag --modedisable 11. Enter the ag --modeshow command to verify that AG mode is disabled. switch:admin> ag --modeshow Access Gateway mode is NOT enabled Port state description The following table describes the possible port states. TABLE 3 Port state description State Description No _Card No _Module Mod_Val Mod_Inv No_Light No_Sync In_Sync Laser_Flt Port_Flt Diag_Flt Lock_Ref Testing Offline Online No interface card present No module (GBIC or other) present Module validation in process Invalid module The module is not receiving light Receiving light but out of sync Receiving light and in sync Module is signaling a laser fault Port marked faulty Port failed diagnostics Locking to the reference signal Running diagnostics Connection not established (only for virtual ports) The port is up and running Access Gateway Administrator's Guide 9 53-1001760-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Access Gateway Administrator’s Guide
9
53-1001760-01
Enabling and disabling Access Gateway mode
2
When you disable AG mode, The switch automatically reboots and comes back online using the
fabric switch configuration; the AG parameters, such as port mapping, and Failover and
Failback are automatically removed. When the switch reboots, it starts in Fabric OS Native
mode. To re-join the switch to the core fabric, refer to
“Rejoining Fabric OS switches to a fabric”
on page 67.
9.
Enter the
switchDisable
command to disable the switch.
switch:admin>
switchdisable
10.
Enter the
ag
command with the
--
modedisable
operand to disable AG mode.
switch:admin>
ag --modedisable
11.
Enter the
ag
--
modeshow
command to verify that AG mode is disabled.
switch:admin>
ag --modeshow
Access Gateway mode is NOT enabled
Port state description
The following table describes the possible port states.
TABLE 3
Port state description
State
Description
No _Card
No interface card present
No _Module
No module (GBIC or other) present
Mod_Val
Module validation in process
Mod_Inv
Invalid module
No_Light
The module is not receiving light
No_Sync
Receiving light but out of sync
In_Sync
Receiving light and in sync
Laser_Flt
Module is signaling a laser fault
Port_Flt
Port marked faulty
Diag_Flt
Port failed diagnostics
Lock_Ref
Locking to the reference signal
Testing
Running diagnostics
Offline
Connection not established (only for virtual ports)
Online
The port is up and running