HP AD510A HP StorageWorks 1500 Modular Smart Array installation guide (355901
HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard Drive Manual
UPC - 829160218625
View all HP AD510A manuals
Add to My Manuals
Save this manual to your list of manuals |
HP AD510A manual content summary:
- HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 1
xx or earlier, with active/passive support Controller firmware 7.0 or later, with active/active support This document details procedures for installing an HP StorageWorks 1500 Modular Smart Array controller shelf (MSA1500) and its attached storage enclosures. This guide is a companion to the MSA1500 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 2
HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP ® is a registered trademark of The Open Group. HP StorageWorks 1500 Modular Smart Array installation guide - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 3
(capacity 27 Step 2: Prepare your site 28 Provide adequate structural support for the floor 28 Provide adequate clearance space and ventilation 28 Provide adequate and redundant sources of power 28 Step 3: Install MSA option kits 30 Step 4: Rack the MSA and the storage enclosures 31 Rack - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 4
Fibre Channel cables in a multipath configuration 48 Connecting the power cords 49 Step 10: Power on the devices 52 Verify the operating status of the the storage 71 4 Configuration procedures-HP-UX environments 73 Prerequisites 73 Additional HP-UX support notes 74 Installing the ACU-CLI on - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 5
if necessary 94 Configuring the storage 94 8 Powering off and powering on the MSA 97 Powering off the MSA 97 Powering on the MSA 98 A Regulatory notices 101 Prevention methods 105 Grounding methods 105 C Worksheets 107 Index 121 HP StorageWorks 1500 Modular Smart Array installation guide 5 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 6
websites 18 4 RAID level comparison 26 5 MSA1500 specifications 29 6 Supported and Unsupported SCSI cable connections 43 7 Levels of protection against power failures 49 8 MSA1500 startup status lights 53 9 MSA1500 startup messages 54 10 HP-UX required updates for active/active 74 11 OpenVMS - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 7
Services>HP StorageWorks Disk Arrays includes: • Physical installation of the MSA • Virtual disk design and configuration of the MSA • Service planning • Service deployment • Installation Verification Testing (IVT) • Customer orientation HP StorageWorks 1500 Modular Smart Array installation guide - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 8
and service guide • MSA1000/1500 Command Line Interface user guide • MSA1000/1500 firmware updating guide • HP array configuration reference guide (ACU section only) • MSA1500 application notes, including instructions for migrating to active/active array controllers (for each supported operating - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 9
Medium blue text: Figure 1 Medium blue, underlined text (http://www.hp.com) Bold font Element Cross-reference links and e-mail addresses Website addresses information or specific instructions. NOTE: Provides additional information. HP StorageWorks 1500 Modular Smart Array installation guide 9 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 10
hardware for which this guide pertains. They have area contains no operator serviceable parts. WARNING: To power cords to completely disconnect power from the power supplies and systems. Any product or assembly marked with these symbols indicates that the component exceeds the recommended weight - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 11
full weight of drivers, firmware documentation updates, and instant access to numerous other product resources. • After signing up, you can quickly locate your products by selecting Business support and then Storage under Product Category. HP StorageWorks 1500 Modular Smart Array installation guide - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 12
Elsewhere, see the HP website: http://www.hp.com. Click Contact HP to find locations and telephone numbers. Helpful websites For third-party product information, see the following HP websites: • http://www.hp.com • http://www.hp.com/go/storage • http://www.hp.com/support/ • http://www.docs.hp.com 12 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 13
Step 2: Prepare your site, page 28 • Step 3: Install MSA option kits, page 30 • Step 4: Rack the MSA and the storage enclosures, Power on the devices, page 52 • Step 11: Configure your MSA, page 56 NOTE: • HP recommends installing and configuring your MSA in the sequence of steps listed in this guide - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 14
5 9 1 Review/confirm your plans 2 Prepare your site 3 Install MSA option kits ~A ~B ~A ~B 4 Rack the MSA 5 Install the hard drives 6 Prepare the servers 7 Install the HBAs 8 Prepare the switches 9 Connect the cables 10 Power on the devices 11 Configure the MSA Figure 1: Overview of MSA - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 15
Step 1: Review and confirm your plans Before installing the MSA, HP recommends thorough research and study to develop the best installation and firmware version (and associated Support Software CD) to use, review the requirements and information in the compatibility guide documents, release notes, - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 16
I/O module) and upgraded firmware Windows HP-UX Linux NetWare OpenVMS Tru64 UNIX SCO VMware IMPORTANT: Supported operating system and network configuration restrictions exist. For more information, see the compatibility guide on the MSA1500 website: http://www.hp.com/go/msa1500cs. 16 Installation - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 17
requirement. • For information on upgrading the MSA to active/active, see the migration instructions for your operating system, available on the Technical documentation page of the MSA1500 website: http://www.hp.com/go/msa1500cs. Complete the planning worksheet on the poster The printed installation - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 18
information http://www.hp.com/go/msa1500cs • Compatibility guide-supported operating systems, Support website Support http://www.hp.com/support Latest support information about all HP products, including the MSA1500: • Available downloads for firmware, software, and drivers • Troubleshooting - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 19
. Other multipath software already present on the host may not be compatible with HP Full Featured MPIO. See the MSA1500 compatibility guide for details. The HP full-featured MPIO is provided on the MSA Support Software CD. Multipathing software for Windows (active/passive environments only) Used in - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 20
for Linux environments. This multipathing tool is included with the QLogic HBA driver on the MSA Support Software CD. Emulex MultiPulse Path Failover for Linux http://h18006.www1.hp.com/products/ sanworks/softwaredrivers/multipathoptions /linux.html Multipathing tool for Linux (active/active - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 21
installation plans and read current information about the device: http://www.hp.com/go/msa1500cs. • Prepare for the installation by reviewing the in this guide may result in lost time and lost revenue while troubleshooting the issues. For example, in a Windows environment, when you power up the - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 22
your environment includes multiple servers, HP recommends designating one of the servers drivers, always use the drivers and installation scripts provided on the MSA Support Software CD and the MSA1500 website. The MSA will not operate as intended if you update your HBA driver manually or use drivers - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 23
is power-cycled, manually HP HP instructions will override the MSA instructions, resulting in additional processing time and reduced performance. • In Windows environments, HBA load balancing is set in the HP MPIO DSM Manager. • In Linux environments, HBA load balancing is set via a driver • Manual load - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 24
. NOTE: After completing the service and re-applying power to the MSA, if necessary, restart the server to rediscover the connection to the MSA controller. For more information, see the HP StorageWorks 1500 Modular Smart Array maintenance and service guide, available on the Technical documentation - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 25
first being disabled, the active controller might halt. To clear this fault condition, you must power-cycle the MSA. For more information, see the HP StorageWorks 1500 Modular Smart Array maintenance and service guide, available on the Technical documentation page of the MSA1500 website: http://www - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 26
• Vertical striping-Offers ultimate fault tolerance and performance, but at the price of storage efficiency. • Horizontal striping-Allows for the creation of large arrays and efficient use of storage capacity, but at the price of I/O performance and less fault tolerance. In a vertical configuration, - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 27
NOTE: For detailed information about the different RAID levels, see the HP Array Configuration Utility User Guide. This guide is available on the Documentation CD and on the Technical documentation page of the MSA1500 website: http://www.hp.com/go/msa1500cs. Hard drive sizes and types Hard drives in - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 28
HP website: http://h30099.www3.hp.com/configurator. In addition to the following discussion, see Table 5, "MSA1500 specifications" on page 29 for a detailed list of site requirements. Provide adequate structural support for the floor Calculate the total weight to allow for servicing and airflow. If - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 29
*Input power and heat dissipation specifications are maximum values and apply to worst-case conditions at full-rated power supply load. The power/heat dissipation for your installation varies depending on the equipment configuration. HP StorageWorks 1500 Modular Smart Array installation guide 29 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 30
HBAs in each server. NOTE: When installing additional SCSI I/O modules, HP recommends populating the SCSI I/O module bays from right-to-left, so . For information about installing the options, see the instructions that came with the option kit. Go to Table 12: "MSA1500 information" on page - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 31
supported for use with the MSA and its storage enclosures, read the compatibility guide, located on the Technical documentation page of the MSA1500 website: http://www.hp such as uninterruptable power supplies (UPS during removal or installation, if the weight, as assembled for shipping, exceeds 22 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 32
the rack are extended to the floor. • The full weight of the rack rests on the leveling jacks. • The following instructions to install the MSA and its storage enclosures: 1. Use the provided rack template as a guide to the round-hold pins provided with the rail kit. WARNING! The pins in the rails - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 33
toward the inside rear of the rack until the pins extend through the holes marked during the rack template procedure and the locking latch engages. HP StorageWorks 1500 Modular Smart Array installation guide 33 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 34
d. Loosen the locking nut on the shipping retaining bracket and slide the bracket to the farthest position on the rear of the rail. 2 1 e. Repeat steps a through d for the left rack rail. 4. Install the component in the rack: a. Remove the bezel from the front of the device, align the device with - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 35
the bracket forward (2) until the tab engages the slot in the chassis. 2 1 d. Tighten the thumbscrew on the bracket. e. Repeat these steps for the other rail. HP StorageWorks 1500 Modular Smart Array installation guide 35 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 36
list of supported hard drives, see the compatibility guide, located on the Technical documentation page of the MSA1500 website: http://www.hp.com/go the enclosure documentation. For information about installing hard drives, see the instructions that came with the hard drive and the enclosure. Go to - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 37
that you perform your SAN management tasks. (Instructions for installing the ACU are included later in this guide.) • Verify that all servers that will access supported for use with the MSA see the compatibility guide, located on the Technical documentation page of the MSA1500 website: http://www.hp - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 38
and the compatibility guide, located on the Technical documentation page of the MSA1500 website: http://www.hp.com/go/ power is removed from the server when installing the HBA, and do not apply power until instructed. Powering on the server before instructed may cause an unsupported HBA driver - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 39
use with the MSA, and that you upgrade the switch firmware to a supported level. For a list of supported switches, see the compatibility guide, located on the Technical documentation page of the MSA1500 website: http://www.hp.com/go/msa1500cs. • For newly installed switches, change the IP address of - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 40
the SCSI cables • Connecting the Fibre Channel cables • Connecting the power cords Each of these connection types is discussed in the following paragraphs SAN switch that is connected to the passive controller in the MSA1500. HP recommends the following: • Connect the first Fibre Channel HBA that is - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 41
has already failed and failover did not occur to the passive server, shut down the passive server and cycle the power to ensure that the MSA1500 is recognized. See "Powering off and powering on the MSA" on page 97 for instructions. HP StorageWorks 1000 Modular Smart Array installation guide 41 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 42
to the storage enclosures, use standard VHDCI SCSI cables included in the shipping carton with each storage enclosure. Recommended SCSI cable connections HP recommends installing additional SCSI I/O modules and connecting storage enclosures in the same sequence as the pre-assigned box numbers, as - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 43
3 and Figure 4 for illustrations of sample configurations. Table 6 Supported and Unsupported SCSI cable connections Supported Unsupported SATA 15242 SATA 15264 SATA SATA 15243 SATA SCSI 15245 SCSI 15244 SCSI SCSI 15246 HP StorageWorks 1500 Modular Smart Array installation guide 43 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 44
Connecting the MSA to SATA storage enclosures The following illustration shows the MSA1500 connected to two MSA20 SATA storage enclosures. NOTE: Tighten the thumbscrews on the SCSI cables to ensure a secure connection. Figure 3 SCSI cable connections to two MSA20 SATA storage enclosures 44 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 45
SCSI storage enclosure. NOTE: Tighten the thumbscrews on the SCSI cables to ensure a secure connection. Figure 4 SCSI cable connections to one MSA30 SCSI storage enclosure HP StorageWorks 1500 Modular Smart Array installation guide 45 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 46
Channel cable will either damage the cable or cause performance problems, including intermittent difficulties accessing the storage. • Whenever a • Make certain that the Fibre Channel cables are installed and supported so that no excess weight is placed on the connectors. This prevents damage to the - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 47
5 shows the Fibre Channel cable connections of an MSA1500 being accessed by two servers in a singlepath configuration. Figure 5 Sample Fibre Channel cable connections, singlepath configuration HP StorageWorks 1500 Modular Smart Array installation guide 47 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 48
Connecting Fibre Channel cables in a multipath configuration Figure 6 shows the Fibre Channel cable connections of an MSA1500 being accessed by two servers in a multipath configuration. For consistency, cabling should be done like this for active/passive and active/active configurations. NOTE: - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 49
to... Provide this level of protection... One power source Protects you from downtime when one of the MSA power supplies fails. The remaining power supply/fan module can operate the MSA until you install a replacement module. HP StorageWorks 1500 Modular Smart Array installation guide 49 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 50
sources fails, due to a pulled cable, tripped breaker, or local power outage. The remaining power source or the UPS will power the MSA until power is restored to the source. Depending on the cause and duration of the power outage, you can use this time to properly shut down your storage sub-system - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 51
placed against it. Pay particular attention to the plug, electrical outlet, and the point where the cord is attached to the MSA. Figure 7 Connecting the power cords using two UPSs HP StorageWorks 1500 Modular Smart Array installation guide 51 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 52
next step only after the Startup Complete message is displayed. If you power on (or restart) the server before the MSA array completes its start- up sequence, the server may not properly discover the storage. 6. Power on the servers in the SAN with access to the MSA, start the operating - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 53
the MSA. • Check the availability of your power source. • Review the setup instructions in the previous sections of this guide. • Remove and reinsert the module. • Refer to the HP StorageWorks 1500 Modular Smart Array maintenance and service guide, available on the Documentation CD and the Technical - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 54
installed the HBA in the server, you have not yet installed the drivers for the HBA and the MSA. You may safely ignore this message power source • Review the setup instructions in the previous sections of this guide • Refer to the HP StorageWorks 1500 Modular Smart Array maintenance and service guide - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 55
and then open a software application or your browser. If your server is not operating properly, see the documentation that came with the server for help. HP StorageWorks 1500 Modular Smart Array installation guide 55 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 56
MSA is physically installed, connected, and powered on, you may customize the server to the Software, Firmware & Drivers page of the MSA1500 website: http://www.hp.com/go/msa1500cs. CAUTION: or support software CD ISO image from the Web. NOTE: When instructed in later sections of this guide, install - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 57
of HP array configurations. • Includes easy to use configuration wizards. • Allows the setting of access rights to MSA storage by hosts. • Supports local or remote access. • Runs online (from the server) in Windows and Linux environments. HP StorageWorks 1500 Modular Smart Array installation guide - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 58
or remotely through HP Systems Insight Manager (HP-SIM). NOTE: The ACU-CLI is included on the Support Software CD inside the MSA1000/1500 Setup and Management kit. Instructions for installing the ACU-CLI on your server are included in the configuration chapters of this guide. For information about - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 59
Configuration procedures-Windows environments, page 61 • Chapter 3: Configuration procedures-Linux environments, page 67 • Chapter 4: Configuration procedures-HP-UX environments, page 73 • Chapter 5: Configuration procedures-OpenVMS environments, page 79 • Chapter 6: Configuration procedures-VMware - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 60
60 Installation procedures-All deployments - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 61
the following paragraphs. NOTE: HP recommends installing your MSA in the sequence of steps listed here and in chapter 1 of this guide. Specific dependencies exist, version installed on the server is supported for use with the MSA. For a current listing of supported operating system versions, see the - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 62
With the HBAs installed in the server, power on the server and start your Windows operating system. NOTE: If the New Hardware Wizard is displayed, click Cancel to prevent installation of an HBA driver that is unsupported for use with the MSA. 2. Insert the MSA Support Software CD in the CD-ROM drive - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 63
for use with the MSA. b. Install the following component (required): • HBA driver (and the included Windows Event Notification Service) IMPORTANT: After installing the HBA and Event Notification Service drivers, remove the Support Software CD from the CD-ROM drive and restart the server. Then, re - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 64
use" on page 15 • "Obtain desired controller firmware and Support Software CD versions" on page 56 For instructions on updating MSA controller firmware, see the HP StorageWorks Modular Smart Array 1000/1500 firmware updating guide, available on the Technical documentation page of the MSA1500 website - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 65
configuration utility. Refer to the appropriate user documentation for instructions. Go to Table 15: "Hard drive information" on page 114 and Table 16: "Array (LUN) information" on page 118 to record information about your storage. HP StorageWorks 1500 Modular Smart Array installation guide 65 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 66
66 Configuration procedures-Windows environments - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 67
following paragraphs. NOTE: HP recommends installing your MSA in the sequence of steps listed here and in chapter 1 of this guide. Specific dependencies exist, version installed on the server is supported for use with the MSA. For a current listing of supported operating system versions, see the - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 68
the server, power on the server and start up the Linux operating system. 2. From the console, log on as the root user. 3. Insert the Support Software CD in this guide. 6. To install the HBA drivers: CAUTION: Use only the Support Software CD to install the HBA drivers. Drivers for all supported HBAs - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 69
driver from source code or manually patch the Linux kernel, see the README file in the /opt/hp/src/hp_qla2x00src directory on the server. 7. To install the HP ACU or the ACU-CLI, see ACU online help or the HP Array Configuration Utility User Guide. a. Navigate to the /ACU/Linux/x86 directory on the - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 70
page 15 • "Obtain desired controller firmware and Support Software CD versions" on page 56 For instructions on updating MSA controller firmware, see the MSA 1000/1500 firmware updating guide, available on the MSA1500 website: http://www.hp.com/go/msa1500cs. IMPORTANT: After updating MSA controller - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 71
manually specify the preferred controller path for each LUN.) If HBA load balancing is also enabled at the host, the host instructions will override the MSA instructions, resulting in additional processing time and reduced performance. In Linux environments, HBA load balancing is set via a driver - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 72
72 Configuration procedures-Linux environments - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 73
following paragraphs. NOTE: HP recommends installing your MSA in the sequence of steps listed here and in chapter 1 of this guide. Specific dependencies exist, version installed on the server is supported for use with the MSA. For a current listing of supported operating system versions, see the - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 74
: The Event Monitoring Service (EMS) is native to the HP-UX operating system as part of the online diagnostics tools. For full information about available support tools, see the EMS Hardware Monitors user's guide and other documents located on the HP diagnostics website: http://docs.hp.com/hpux/diag - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 75
. See the ACU or CLI online help or user documentation for instructions. • LUN configuration notes: • In direct connect environments or in ACU-CLI online help, the HP-UX ACU-CLI readme file or release notes, or the HP Configuring Arrays reference guide. 1. Insert the Support Software CD in the CD - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 76
page 15 • "Obtain desired controller firmware and Support Software CD versions" on page 56 For instructions on updating MSA controller firmware, see the MSA 1000/1500 firmware updating guide, available on the MSA1500 website: http://www.hp.com/go/msa1500cs. IMPORTANT: After updating MSA controller - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 77
• In active/active configurations, manually assign a preferred path (controller instructions. Go to Table 15: "Hard drive information" on page 114 and Table 16: "Array (LUN) information" on page 118 to record information about your storage. HP StorageWorks 1500 Modular Smart Array installation guide - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 78
78 Configuration procedures-HP-UX environments - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 79
following paragraphs. NOTE: HP recommends installing your MSA in the sequence of steps listed here and in chapter 1 of this guide. Specific dependencies exist, version installed on the server is supported for use with the MSA. For a current listing of supported operating system versions, see the - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 80
Obtaining World Wide Port Names When setting connections to the MSA, you must supply the WWPNs of the Fibre Channel adapters on the OpenVMS system. To obtain the WWPNs: 1. From OpenVMS, use the following DCL command: $ show device fg/full The following information is displayed: Device FGA0: device - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 81
. For instructions, see your version-specific OpenVMS upgrade and installation manual. d. Install the Fibre_SCSI patch on all system disks. For instructions, see the documentation that came with the kit. e. Restart the OpenVMS server. HP StorageWorks 1500 Modular Smart Array installation guide 81 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 82
page 15 • "Obtain desired controller firmware and Support Software CD versions" on page 56 For instructions on updating MSA controller firmware, see the MSA 1000/1500 firmware updating guide, available on the MSA1500 website: http://www.hp.com/go/msa1500cs. IMPORTANT: After updating MSA controller - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 83
server have been granted access to the storage. • In active/active configurations, manually assign a preferred path (controller ownership) for each LUN. By default, MSA MSA 1000/1500 Command Line Interface user guide for specific instructions. HP StorageWorks 1500 Modular Smart Array installation - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 84
84 Configuration procedures-OpenVMS environments - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 85
following paragraphs. NOTE: HP recommends installing your MSA in the sequence of steps listed here and in chapter 1 of this guide. Specific dependencies exist, version installed on the server is supported for use with the MSA. For a current listing of supported operating system versions, see the - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 86
page 15 • "Obtain desired controller firmware and Support Software CD versions" on page 56 For instructions on updating MSA controller firmware, see the MSA 1000/1500 firmware updating guide, available on the MSA1500 website: http://www.hp.com/go/msa1500cs. IMPORTANT: After updating MSA controller - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 87
less than the number of LUNs you have presented, you will not see all of your LUNs. The maximum value for this field is 256. HP StorageWorks 1500 Modular Smart Array installation guide 87 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 88
3. Verify that the value is large enough to support your configuration. If the value is less than the For installation and configuration instructions, see the Guest Operating System Installation Guide on the VMware website: power on the virtual machine. 88 Configuration procedures-VMware environments - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 89
• Ensure that the drivers for the SCSI and network manually assign the preferred path for each LUN. Perform these tasks using your chosen configuration utility. Refer to the appropriate user documentation for procedural instructions. HP StorageWorks 1500 Modular Smart Array installation guide - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 90
Go to Table 15: "Hard drive information" on page 114 and Table 16: "Array (LUN) information" on page 118 to record information about your storage. 90 Configuration procedures-VMware environments - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 91
following paragraphs. NOTE: HP recommends installing your MSA in the sequence of steps listed here and in chapter 1 of this guide. Specific dependencies exist, version installed on the server is supported for use with the MSA. For a current listing of supported operating system versions, see the - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 92
MSA-CLI to configure the storage and obtain the HBA drivers and multipathing tools from a different source, such as through operating system updates or the HP website. NetWare environments • Single-controller configurations are supported for use with active/passive firmware only. • Dual-controller - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 93
/active, see the migration instructions for Tru64 UNIX environments, available on the Technical documentation page of the MSA1500 website: http://www.hp.com/go/msa1500cs. SCO UNIX environments • Dual-controller active/passive configurations are not supported. Dual-controller configurations must - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 94
page 15 • "Obtain desired controller firmware and Support Software CD versions" on page 56 For instructions on updating MSA controller firmware, see the MSA 1000/1500 firmware updating guide, available on the MSA1500 website: http://www.hp.com/go/msa1500cs. IMPORTANT: After updating MSA controller - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 95
• In active/active configurations, manually assign a preferred path (controller instructions. Go to Table 15: "Hard drive information" on page 114 and Table 16: "Array (LUN) information" on page 118 to record information about your storage. HP StorageWorks 1500 Modular Smart Array installation guide - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 96
96 Configuration procedures-Other environments - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 97
five seconds to place the MSA array in Standby mode. 5. Verify that the Power on/Standby button LED is amber/off and that the fans are off. 6. Power off all attached hard drive enclosures. 7. Disconnect the power cords from the MSA. HP StorageWorks 1500 Modular Smart Array installation guide 97 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 98
messages and look for the following message: Startup Complete IMPORTANT: Proceed to the next step only after the Startup Complete message is displayed. If you power on (or restart) the server before the MSA array completes its start-up sequence, the server may not properly discover the storage - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 99
installation of an unsupported HBA driver. The required drivers are provided on the MSA1000/1500 Support Software CD, shipped with the device and available on the MSA websites. 7. Verify that each device in the SAN is operating properly. HP StorageWorks 1500 Modular Smart Array installation guide 99 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 100
100 Powering off and powering on the MSA - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 101
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a du Règlement sur le matériel brouilleur du Canada. HP StorageWorks 1500 Modular Smart Array installation guide 101 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 102
(in brackets are the equivalent international standards): • EN55022 (CISPR 22) - Electromagnetic Interference • EN50082-1 (IEC801-2, IEC801-3, IEC801-4) - Electromagnetic Immunity • EN60950 (IEC950) - Product Safety Japanese notice Japanese power cord notice BSMI notice 102 Regulatory notices - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 103
other than those specified herein or in the laser product's installation guide may result in hazardous radiation exposure. To reduce the risk of laser device other than those specified herein. • Allow only HP Authorized Service technicians to repair the unit. The Center for Devices and - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 104
designated for this product. For more information about battery replacement or proper disposal, contact your HP Authorized Reseller or your Authorized Service Provider. WARNING! Your Accelerator Array contains Lithium Manganese Dioxide, Nickel-Metal Hydride, or Vanadium Pentoxide batteries. There - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 105
field service kit with a folding static-dissipating work mat. If you do not have any of the equipment suggested for proper grounding, either have an HP Authorized Reseller product installation, contact your HP Authorized Reseller. HP StorageWorks 1500 Modular Smart Array installation guide 105 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 106
106 Electrostatic discharge - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 107
of the information is required for multipathing, future configuration changes, and troubleshooting purposes. The following worksheets are included in this section: • • Hard drive information, page 114 • Array (LUN) information, page 118 HP StorageWorks 1500 Modular Smart Array installation guide 107 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 108
-servers MSA1500 Serial number (on the product label) Controller firmware: Version shipped on the controller Version available on the Web Support Software CD: Version shipped with the MSA Version available on the Web MSA1500 WWNN MSA1500 WWPN Fibre Channel interconnect device (switch - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 109
version Switch IP address Switch WWNN Switch WWPN Any other interconnect device Make and model Switch firmware version Switch IP address Switch WWNN Switch WWPN HP StorageWorks 1500 Modular Smart Array installation guide 109 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 110
Table 14 Server information Component Primary server Make and model Operating system and version / kernel Service pack / errata Server name HBA model HBA server slot location HBA firmware version HBA driver version HBA boot BIOS firmware HBA WWNN HBA WWPN (also called Adapter ID) Setting - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 111
model Operating system and version / kernel Service pack / errata Server name HBA model HBA server slot location HBA firmware version HBA driver version HBA boot BIOS firmware HBA WWNN must be the same as the companion device HP StorageWorks 1500 Modular Smart Array installation guide 111 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 112
14 Server information (continued) Component Additional server Make and model Operating system and version / kernel Service pack / errata Server name HBA model HBA server slot location HBA firmware version HBA driver version HBA boot BIOS firmware HBA WWNN HBA WWPN (also called Adapter ID) Setting - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 113
model Operating system and version / kernel Service pack / errata Server name HBA model HBA server slot location HBA firmware version HBA driver version HBA boot BIOS firmware HBA WWNN must be the same as the companion device HP StorageWorks 1500 Modular Smart Array installation guide 113 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 114
Table 15 Hard drive information Box number Drive bay Transfer rate Drive capacity Spindle speed 1 2 3 4 Box number 5 assigned to this enclosure 6 7 ________ 8 9 10 11 12 13 14 Array letter (LUN #) NOTE: Recording information about the hard drives and their configuration is a two-step - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 115
based on their connection to the MSA1500. See Figure 2 "SCSI I/O modules, bus numbers, and box numbers" on page 42 for the box number assignment pattern. HP StorageWorks 1500 Modular Smart Array installation guide 115 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 116
Table 15 Hard drive information (continued) Box number Drive bay Transfer rate Drive capacity Spindle speed 1 2 3 4 Box number 5 assigned to this enclosure 6 7 ________ 8 9 10 11 12 13 14 Array letter (LUN #) 116 Worksheets - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 117
Table 15 Hard drive information (continued) Box number Drive bay Transfer rate Drive capacity Spindle speed 1 2 3 4 Box number 5 assigned to this enclosure 6 7 ________ 8 9 10 11 12 13 14 Array letter (LUN #) HP StorageWorks 1500 Modular Smart Array installation guide 117 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 118
Table 16 Array (LUN) information Basic settings SSP (ACL) settings Array letter (LUN #) Capacity RAID level HBA (WWPN or name) Host mode (profile) O/S share name 118 Worksheets - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 119
Table 16 Array (LUN) information (continued) Basic settings SSP (ACL) settings Array letter (LUN #) Capacity RAID level HBA (WWPN or name) Host mode (profile) O/S share name HP StorageWorks 1500 Modular Smart Array installation guide 119 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 120
Table 16 Array (LUN) information (continued) Basic settings SSP (ACL) settings Array letter (LUN #) Capacity RAID level HBA (WWPN or name) Host mode (profile) O/S share name 120 Worksheets - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 121
Windows environments 63 supported operating systems 57 audience 7, 8 authorized reseller, HP 12 B battery illustrated 47 connecting power cords, illustrated 51 connecting SCSI cables, illustrated 44 fiber 46 power 49 SCSI 42 firmware HP StorageWorks 1500 Modular Smart Array installation guide 121 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 122
support 11 HP-UX environments additional notes 74 configuring the storage 76 installing the ACU-CLI 75 prerequisites for the MSA 73 updating MSA firmware 76 I Infrastructure website 18 Insight Manager website 18 installing hard drives 36 122 option kits installing the HBA driver 68 installing the - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 123
option kits supported and unsupported 43 Secure Path website 18 securing the system to the rack 35 server at MSA startup 55 designating a management server 37 preparing for use with the MSA 37 setup illustrated steps 14 listed steps 13 HP StorageWorks 1500 Modular Smart Array installation guide - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 124
Power on the devices 52 Step 11: Configure your MSA 56 Step 2: Prepare your site 28 Step 3: Install MSA option kits choice, HP 11 support software CD using in HP-UX power related 50 symbols on equipment 10 websites HP documentation 8 HP storage 12 HP Subscriber's choice 11 MSA and SAN 18 weight - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 125
installing the ACU-CLI 63 installing the HBA driver 62 prerequisites for the MSA 61 updating MSA firmware 64 HP StorageWorks 1500 Modular Smart Array installation guide 125 - HP AD510A | HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 126
126
*355901-005*
355901–005
HP StorageWorks
1500 Modular Smart Array
installation guide
Product Version:
Controller firmware 5.xx or earlier, with active/passive support
Controller firmware 7.0 or later, with active/active support
This document details procedures for installing an HP StorageWorks 1500 Modular Smart Array controller
shelf (MSA1500) and its attached storage enclosures. This guide is a companion to the MSA1500 Installation
Overview poster.
Note:
Two versions of firmware are available for the MSA1500: active/passive and active/active. For more
information, see “
Step 1: Review and confirm your plans”
(in this guide) and the compatibility guides on the
MSA1500 website:
.
Part number: 355901–005
Fifth edition: June 2007