HP AD510A HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 38

Step 7: Install the HBA in your servers

Get HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard Drive PDF manuals and user guides
UPC - 829160218625
View all HP AD510A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Step 7: Install the HBA in your servers After you have confirmed that your servers are operating properly, install the HBA for the MSA in each server that will access the MSA. Because the MSA can be deployed into a variety of operating system environments and configurations (including singlepath and multipath), specific HBAs are required for the different deployments. To confirm that you purchased the correct HBA for your configuration, read the release notes and the compatibility guide, located on the Technical documentation page of the MSA1500 website: http://www.hp.com/go/msa1500cs. NOTE: Plan to set up Selective Storage Presentation (SSP) or Access Control Lists (ACLs) to control access to the LUNs to the appropriate HBAs. Even in the same OS environment, if multiple servers and HBAs have access to the same LUN, all of the HBAs must be of the same model. CAUTION: Be sure that power is removed from the server when installing the HBA, and do not apply power until instructed. Powering on the server before instructed may cause an unsupported HBA driver to be installed automatically by the operating system. For information about installing the HBA, see the instructions that came with the HBA or the server. Go to Table 14: "Server information" on page 110 to record information about the HBA in each server that will connect to the MSA. Some information may be printed on the HBA or on its shipping carton. If this information is not available now, you can obtain it later through the Command Line Interface or by viewing the monitor connected to the server during the server power-on self-test (POST). 38 Installation procedures-All deployments

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Installation procedures—All deployments
38
Step 7: Install the HBA in your servers
After you have confirmed that your servers are operating properly, install the HBA for the MSA in
each server that will access the MSA.
Because the MSA can be deployed into a variety of operating system environments and
configurations (including singlepath and multipath), specific HBAs are required for the different
deployments.
To confirm that you purchased the correct HBA for your configuration, read the release notes and
the compatibility guide, located on the Technical documentation page of the MSA1500 website:
.
NOTE:
Plan to set up Selective Storage Presentation (SSP) or Access Control Lists (ACLs) to control
access to the LUNs to the appropriate HBAs. Even in the same OS environment, if multiple servers
and HBAs have access to the same LUN, all of the HBAs must be of the same model.
CAUTION:
Be sure that power is removed from the server when installing the HBA, and do not
apply power until instructed.
Powering on the server before instructed may cause an unsupported HBA driver to be installed
automatically by the operating system.
For information about installing the HBA, see the instructions that came with the HBA or the server.
Go to
Table 14
: ”
Server information
” on page110 to record information about the HBA in each
server that will connect to the MSA. Some information may be printed on the HBA or on its shipping
carton. If this information is not available now, you can obtain it later through the Command Line
Interface or by viewing the monitor connected to the server during the server power-on self-test
(POST).