HP Cisco MDS 9124 Cisco Nexus 5000 Series Hardware Installation Guide (OL-1590 - Page 80

Removing a Cable from an SFP Transceiver,

Get HP Cisco MDS 9124 - Fabric Switch PDF manuals and user guides View all HP Cisco MDS 9124 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

Connecting to a Fibre Channel Port Chapter 3 Connecting the Cisco Nexus 5000 Switch Send documentation comments to [email protected] Figure 3-4 Connecting the LC-Type Cable to a Fibre Channel Port LC plug SFP module 91681 Caution If the cable does not install easily, ensure that it is correctly positioned before continuing. For instructions on verifying connectivity, see the Cisco Nexus 5000 Series CLI Configuration Guide. Removing a Cable from an SFP Transceiver Caution When pulling a cable from a transceiver, grip the body of the connector. Do not pull on the jacket sleeve, because this action can compromise the fiber-optic termination in the connector. Caution If the cable does not remove easily, ensure that any latch present on the cable has been released before continuing. To remove the cable, follow these steps: Step 1 Step 2 Step 3 Step 4 Attach an ESD-preventive wrist strap and follow its instructions for use. Press the release latch on the cable, grasp the connector near the connection point, and gently pull the connector from the transceiver. Insert a dust plug into the cable end of the transceiver. Insert a dust plug onto the end of the cable. 3-10 Cisco Nexus 5000 Series Hardware Installation Guide OL-15902-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
Send documentation comments to [email protected]
3-10
Cisco Nexus 5000 Series Hardware Installation Guide
OL-15902-01
Chapter 3
Connecting the Cisco Nexus 5000 Switch
Connecting to a Fibre Channel Port
Figure 3-4
Connecting the LC-Type Cable to a Fibre Channel Port
Caution
If the cable does not install easily, ensure that it is correctly positioned before continuing.
For instructions on verifying connectivity, see the
Cisco Nexus 5000 Series CLI Configuration Guide
.
Removing a Cable from an SFP Transceiver
Caution
When pulling a cable from a transceiver, grip the body of the connector. Do not pull on the jacket sleeve,
because this action can compromise the fiber-optic termination in the connector.
Caution
If the cable does not remove easily, ensure that any latch present on the cable has been released before
continuing.
To remove the cable, follow these steps:
Step 1
Attach an ESD-preventive wrist strap and follow its instructions for use.
Step 2
Press the release latch on the cable, grasp the connector near the connection point, and gently pull the
connector from the transceiver.
Step 3
Insert a dust plug into the cable end of the transceiver.
Step 4
Insert a dust plug onto the end of the cable.
LC plug
SFP module
91681