HP Cisco MDS 9134 Cisco MDS 9100 Series Hardware Installation Guide (OL-17951- - Page 62

Verifying the Fan Module, Step 1

Get HP Cisco MDS 9134 - Fabric Switch PDF manuals and user guides View all HP Cisco MDS 9134 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Removing and Installing Components Chapter 2 Installing the Cisco MDS 9100 Series Send documentation comments to [email protected] Verifying the Fan Module To verify that the new fan module is installed correctly, follow these steps: Step 1 Step 2 Step 3 Listen for the fans; you should immediately hear them operating. If you do not hear them, ensure that the fan module is inserted completely in the switch and the faceplate is flush with the switch back panel. Verify that the Fan module LED is green. If the LED is orange, then one fan has failed in this fan module; if the LED is red, then both fans have failed in this fan module. Contact your customer service representative for assistance if, after several attempts, the fans do not operate or you experience trouble with the installation. Note Verify that the transceiver and cable type both have LC connectors and are the required type for longwave or shortwave transmission and the required distances. The transceiver label generally lists the model and wavelength. Note If you purchased this product through a Cisco reseller, contact the reseller directly for technical support. If you purchased this product directly from Cisco, contact Cisco Technical Support at this URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtm 2-34 Cisco MDS 9100 Series Hardware Installation Guide OL-17951-02

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Send documentation comments to [email protected]
2-34
Cisco MDS 9100 Series Hardware Installation Guide
OL-17951-02
Chapter 2
Installing the Cisco MDS 9100 Series
Removing and Installing Components
Verifying the Fan Module
To verify that the new fan module is installed correctly, follow these steps:
Step 1
Listen for the fans; you should immediately hear them operating. If you do not hear them, ensure that
the fan module is inserted completely in the switch and the faceplate is flush with the switch back panel.
Step 2
Verify that the Fan module LED is green. If the LED is orange, then one fan has failed in this fan module;
if the LED is red, then both fans have failed in this fan module.
Step 3
Contact your customer service representative for assistance if, after several attempts, the fans do not
operate or you experience trouble with the installation.
Note
Verify that the transceiver and cable type both have LC connectors and are the required type for
longwave or shortwave transmission and the required distances. The transceiver label generally
lists the model and wavelength.
Note
If you purchased this product through a Cisco reseller, contact the reseller directly for technical support.
If you purchased this product directly from Cisco, contact Cisco Technical Support at this URL: