HP Cisco Nexus 5000 Cisco MDS 9000 Family Release Notes for Cisco MDS SAN-OS R - Page 18

ivr refresh, copy running-config startup-config, Step 3

Get HP Cisco Nexus 5000 - Converged Network Switches PDF manuals and user guides View all HP Cisco Nexus 5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Upgrading Your Cisco MDS SAN-OS Software Image Send documentation comments to [email protected] Note Complete Step 2 for all IVR enabled switches before moving to Step 3. Step 3 Step 4 Step 5 Step 6 Step 7 Check the syslogs for any ISL that was isolated. 2005 Aug 31 21:52:04 switch %FCDOMAIN-2-EPORT_ISOLATED: %$VSAN 2005%$ Isolation of interface port-channel 52 (reason: unknown failure) 2005 Aug 31 21:52:04 switch %FCDOMAIN-2-EPORT_ISOLATED: %$VSAN 2005%$ Isolation of interface port-channel 51 (reason: domain ID assignment failure) Issue the following commands for the isolated switches in Step 3: switch(config)# vsan database switch(config-vsan-db)# vsan vsan-id suspend switch(config-vsan-db)# no vsan vsan-id suspend Issue the ivr refresh command to perform an IVR refresh on all the IVR enabled switches. Issue the copy running-config startup-config command to save the RDI mode in the startup configuration on all of the switches. Follow the normal upgrade guidelines for Release 2.1(2b). If you are adding new switches running Cisco MDS SAN-OS Release 2.1(2b) or later, upgrade all of your existing switches to Cisco SAN-OS Release 2.1(2b) as described in this workaround. Then follow the normal upgrade guidelines for Release 3.3(3). Note RDI mode should not be disabled for VSANs running in interop mode 2 or interop mode 3. Cisco MDS 9000 Family Release Notes for Cisco MDS SAN-OS Release 3.3(3) 18 OL-14116-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
Send documentation comments to [email protected]
18
Cisco MDS 9000 Family Release Notes for Cisco MDS SAN-OS Release 3.3(3)
OL-14116-11
Upgrading Your Cisco MDS SAN-OS Software Image
Note
Complete Step 2 for all IVR enabled switches before moving to Step 3.
Step 3
Check the syslogs for any ISL that was isolated.
2005 Aug 31 21:52:04 switch %FCDOMAIN-2-EPORT_ISOLATED:
%$VSAN 2005%$ Isolation of interface
port-channel 52 (reason: unknown failure)
2005 Aug 31 21:52:04 switch %FCDOMAIN-2-EPORT_ISOLATED: %$VSAN 2005%$
Isolation of interface port-channel 51
(reason: domain ID assignment failure)
Step 4
Issue the following commands for the isolated switches in Step 3:
switch(config)#
vsan database
switch(config-vsan-db)#
vsan
vsan-id
suspend
switch(config-vsan-db)# no
vsan
vsan-id
suspend
Step 5
Issue the
ivr refresh
command to perform an IVR refresh on all the IVR enabled switches.
Step 6
Issue the
copy running-config startup-config
command to save the RDI mode in the startup
configuration on all of the switches.
Step 7
Follow the normal upgrade guidelines for Release 2.1(2b). If you are adding new switches running Cisco
MDS SAN-OS Release 2.1(2b) or later, upgrade all of your existing switches to Cisco SAN-OS Release
2.1(2b) as described in this workaround. Then follow the normal upgrade guidelines for Release 3.3(3).
Note
RDI mode should not be disabled for VSANs running in interop mode 2 or interop mode 3.