HP G62-415NR Service Guide - Page 68

disconnect the keyboard cable, Release the zero insertion force ZIF connector

Get HP G62-415NR PDF manuals and user guides View all HP G62-415NR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

3. Turn the computer display-side up with the front toward you. 4. Open the computer as far as possible. 5. Release the tabs along the left (1) and right (2) edges of the keyboard using a thin flat-bladed screwdriver. 6. Lift the rear edge of the keyboard (3), and set the keyboard back towards the display (4). 7. Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is attached and disconnect the keyboard cable (2) from the system board. 8. Remove the keyboard. Reverse this procedure to install the keyboard. 58 Chapter 4 Removal and replacement procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
3.
Turn the computer display-side up with the front toward you.
4.
Open the computer as far as possible.
5.
Release the tabs along the left
(1)
and right
(2)
edges of the keyboard using a thin flat-bladed
screwdriver.
6.
Lift the rear edge of the keyboard
(3)
, and set the keyboard back towards the display
(4)
.
7.
Release the zero insertion force (ZIF) connector
(1)
to which the keyboard cable is attached and
disconnect the keyboard cable
(2)
from the system board.
8.
Remove the keyboard.
Reverse this procedure to install the keyboard.
58
Chapter 4
Removal and replacement procedures
ENWW