HP Integrity rx1620 HP Management Base Installation and User's Guide for Linux - Page 10

Using HP Management Base Utilities, hpia64info—Reports IPMI Information

Get HP Integrity rx1620 PDF manuals and user guides View all HP Integrity rx1620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

3 Using HP Management Base Utilities This chapter describes how to use the HP Management Base command-line utilities. All utilities have manpages. See Appendix B (page 20). NOTE: For all the HP Management Base manpages, you can display a synopsis of options and directives by entering the following: command -? where command is the name of the command. hpia64info-Reports IPMI Information Syntax hpia64info The hpia64info utility lists information obtained from the IPMI Baseboard Management Controller (BMC) on HP Integrity Servers. This information is a fixed set in a fixed format and is used primarily by other HP tools. hpmodel-Reports Hardware Model Information NOTE: The hpmodel utility is available only with HP Management Base version 2.1 and later. Syntax /opt/hp/hpmgmtbase/bin/hpmodel [-a] [-imprsuw] hpmodel reads the system firmware's SMBIOS table to obtain information on HP Integrity servers. The following command options enable you to report system Universally Unique Identifier (UUID), product model name, version, wake-up type, serial number, manufacturer, and platform type: -a Displays all system information obtained from the system table in SMBIOS. -i Displays platform type string (ia64, i686, i386, and so on). -m Displays system manufacturer. -p Displays system product name. -r Displays system product version. -s Displays system serial number. -u Displays system UUID. -w Displays wake-up type (LAN remote, Power Switch, Modem Ring, and so on). 10 Using HP Management Base Utilities

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
3 Using HP Management Base Utilities
This chapter describes how to use the HP Management Base command-line utilities.
All utilities have manpages. See
Appendix B (page 20)
.
NOTE:
For all the HP Management Base manpages, you can display a synopsis of options and
directives by entering the following:
command
-?
where
command
is the name of the command.
hpia64info
—Reports IPMI Information
Syntax
hpia64info
The
hpia64info
utility lists information obtained from the IPMI Baseboard Management
Controller (BMC) on HP Integrity Servers. This information is a fixed set in a fixed format and
is used primarily by other HP tools.
hpmodel
—Reports Hardware Model Information
NOTE:
The
hpmodel
utility is available only with HP Management Base version 2.1 and later.
Syntax
/opt/hp/hpmgmtbase/bin/hpmodel [-a] [-imprsuw]
hpmodel
reads the system firmware's SMBIOS table to obtain information on HP Integrity
servers. The following command options enable you to report system Universally Unique
Identifier (UUID), product model name, version, wake-up type, serial number, manufacturer,
and platform type:
-a
Displays all system information obtained from the system table in SMBIOS.
-i
Displays platform type string (ia64, i686, i386, and so on).
-m
Displays system manufacturer.
-p
Displays system product name.
-r
Displays system product version.
-s
Displays system serial number.
-u
Displays system UUID.
-w
Displays wake-up type (LAN remote, Power Switch, Modem Ring, and so on).
10
Using HP Management Base Utilities