HP LaserJet 3200 HP LaserJet 3200 All-in-One Product (English) Getting Started - Page 39

reappears before installation is complete, click, If you are prompted to restart your computer

Get HP LaserJet 3200 - All-in-One Printer PDF manuals and user guides View all HP LaserJet 3200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Note To install the software for Windows NT 4.0 (direct connect installation with a parallel cable) To install the software on Windows NT 4.0, you must have administrator privileges (on start and restart). w Insert the product software CD-ROM into the CD-ROM drive. x When the welcome screen opens, follow the directions on screen. If the welcome screen does not open, click Start, click Run, type Z:\setup (where Z is the letter of your CDROM disk drive), and then click OK. y Click the button labeled Software Installation. z Continue to step 6 on page 37. Note Note 6 Follow the instructions on the screen to install the software. Before installation is complete, make sure that there is a check mark next to Print a test page (when the prompt appears). In Windows 2000, if the "Found New Hardware Wizard" window reappears before installation is complete, click Cancel. 7 Click Finish. 8 If you are prompted to restart your computer, click Yes. The test page should print after your computer restarts. If you are not prompted to restart your computer, a test page should print immediately. (If you use Windows NT 4.0, you should not have to restart your computer.) 9 Continue to "Check your work #8" on page 38. EN Completing installation 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
EN
Completing installation
37
To install the software for Windows NT 4.0 (direct connect
installation with a parallel cable)
Note
To install the software on Windows NT 4.0, you must have
administrator privileges (on start and restart).
w
Insert the product software CD-ROM into the CD-ROM drive.
x
When the welcome screen opens, follow the directions on
screen. If the welcome screen does not open, click
Start
,
click
Run
, type
Z:\setup
(where
Z
is the letter of your CD-
ROM disk drive), and then click
OK
.
y
Click the button labeled
Software Installation
.
z
Continue to step
6
on page 37.
6
Follow the instructions on the screen to install the software.
Note
Before installation is complete, make sure that there is a check mark
next to
Print a test page
(when the prompt appears).
In Windows 2000, if the
“
Found New Hardware Wizard
”
window
reappears before installation is complete, click
Cancel
.
7
Click
Finish
.
8
If you are prompted to restart your computer, click
Yes
.
Note
The test page should print after your computer restarts. If you are
not
prompted to restart your computer, a test page should print
immediately. (If you use Windows NT 4.0, you should not have to restart
your computer.)
9
Continue to
“
Check your work #8
”
on page 38.