HP ProLiant 1200 Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance an - Page 110

DAAD Diagnostic Messages

Get HP ProLiant 1200 PDF manuals and user guides View all HP ProLiant 1200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

3-56 Diagnostic Tools DAAD Diagnostic Messages Continued Message Description Accelerator Valid data was found in posted status: Valid write memory at reinitialization. data found at reset Data will be flushed to disk. Accelerator Catastrophic problem with status: Warranty array accelerator board. Refer alert to other messages on Diagnostics screen for exact meaning of this message. Adapter/NVRAM EISA nonvolatile RAM has an ID ID mismatch for a different controller from the one physically present in the slot. Battery pack X Battery pack on the array below reference accelerator is below the voltage required voltage levels. Battery X not fully charged Battery is not fully charged. Board not attached NVRAM configuration present, controller not detected Compatibility port problem detected Configuration Array controller configured for use with array accelerator board, but one is not attached. EISA nonvolatile RAM has a configuration for an array controller but there is no board in this slot. Either a board has been removed from the system or a board has been placed in the wrong slot. Compatibility port configured for this IDA controller. When DAAD was verifying this interface, a serious problem was detected. DAAD detected that Recommended Action Not an error or data loss condition. No action needs to be taken. Replace the array accelerator board. Run the System Configuration Utility. Allow enough time for batteries to recharge (36 hours). If batteries have not recharged after 36 hours, replace the array accelerator board. If 75% of the batteries present are fully charged, the array accelerator is fully operational. If more than 75% of the batteries are not fully charged, allow 36 hours to recharge them. Attach array accelerator board to array controller. Place the array controller in the proper slot or run the System Configuration Utility to reconfigure nonvolatile RAM to reflect the removal or new position. A hardware problem has occurred; replace the IDA controller. Run the latest version of

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
3-56
Diagnostic Tools
DAAD Diagnostic Messages
Continued
Message
Description
Recommended Action
Accelerator
status: Valid
data found at
reset
Valid data was found in posted
write memory at reinitialization.
Data will be flushed to disk.
Not an error or data loss
condition. No action needs
to be taken.
Accelerator
status: Warranty
alert
Catastrophic problem with
array accelerator board. Refer
to other messages on
Diagnostics screen for exact
meaning of this message.
Replace the array
accelerator board.
Adapter/NVRAM
ID mismatch
EISA nonvolatile RAM has an ID
for a different controller from
the one physically present in
the slot.
Run the System
Configuration Utility.
Battery pack X
below reference
voltage
Battery pack on the array
accelerator is below the
required voltage levels.
Allow enough time for
batteries to recharge (36
hours). If batteries have not
recharged after 36 hours,
replace the array
accelerator board.
Battery X not
fully charged
Battery is not fully charged.
If 75% of the batteries
present are fully charged,
the array accelerator is fully
operational. If more than
75% of the batteries are
not
fully charged, allow 36 hours
to recharge them.
Board not
attached
Array controller configured for
use with array accelerator
board, but one is not attached.
Attach array accelerator
board to array controller.
NVRAM
configuration
present,
controller not
detected
EISA nonvolatile RAM has a
configuration for an array
controller but there is no board
in this slot. Either a board has
been removed from the system
or a board has been placed in
the wrong slot.
Place the array controller in
the proper slot or run the
System Configuration Utility
to reconfigure nonvolatile
RAM to reflect the removal
or new position.
Compatibility
port problem
detected
Compatibility port configured
for this IDA controller. When
DAAD was verifying this
interface, a serious problem
was detected.
A hardware problem has
occurred; replace the IDA
controller.
Configuration
DAAD detected that
Run the latest version of